cooker

  1. M

    Cooker Socket showing 3 volts when off

    Hi there, wondering if anyone can give me some advice please. In my kitchen I have a cooker switch with a plug socket which I believe is on a dedicated circuit. If I test it with a Voltage Tester it read all correct as it should. Now if I turn off the Mcb on the CU which is labeled "Cooker" it...
  2. R

    Moving cooker switch within prescribed zone

    Hi, With respect to the cooker switch only. If I moved it 400mm to the left by extending the T&E from its original position using crimps, then tile over the original back box, would it satisfy regs by maintaining the modified circuit within the prescribed zone (assuming all other rules are...
  3. UKMeterman

    Shower and cooker circuits shown as 2.5mm2 on shedule but overall condition satisfactory

    I am reviewing a EICR for a property I am buying. The vendor has had the EICR done, but both the Cooker and Shower are on 40A 60898 B curve mcbs and the cable type is shown as 2.5mm2 type A install methord C. I suspect a clerical error but as it is in the vendor document pack what would you...
  4. HappyHippyDad

    Is 0.15M ohms N - E a fault on a cooker?

    Further to my other thread about the connected neutral. I have decided to write (politely) to the rather difficult customer and explain that I was right to indicate that the cooker was potentially dangerous. However, I thought I better check to see if it actually is! I found my results and the...
  5. S

    Add extra 13A sockets to Cooker circuit.

    There is a severe lack of sockets in our kitchen. We have a cooker control switch with a single socket in it, but no cooker connected. Would it be possible to run extra 13A sockets off the cooker control circuit? If so, would this need to be done by an electrician to be complient with regs...
  6. Pretty Mouth

    Open neutral in cooker

    A client has a Kenwood CK405 dual fuel range cooker, for which the smaller of the 2 ovens doesn't work. The elements tested out fine, but live tests showed that both N and L sides of the elements were at 230V to E, so presumably an open neutral. I'm guessing it's a loose connection somewhere...
  7. G

    6mm kitchen radial sockets with cooker on 40amp MCB

    I've been asked to change few double sockets, but not keen on touching after seeing 6mm cable, so did a bit of checking as can see the kitchen 'extension' has been wired in 6mm (red) with a 40amp MCB. The radial has 5 double sockets, including a dishwasher, tumble dryer, washing machine and...
  8. R

    Changing thick cooker wire for standard plug wire at socket

    Hi I am attempting some DIY I had the wire installed as I was going to have an electric cooker. This changed and I now just want to put a double switched socket in the hole. Could someone please tell me how I can convert the wire so it is smaller and fits in the back of a standard switched...
  9. Msitekkie

    PAT IR fail on old cooker with rods not cable

    I am PAT testing a very old 2100W Belling tabletop cooker that the customer is keen to keep & paying me to repair. It fails a L-E or N-E IR test at 0.46 M ohms. Internally the cooker uses bare rods rather than cable. I replaced the old cable & plug and L-N I get > 1999, but L-E or N-E still...
  10. joshimoto

    UK Wiring new Hob / Cooker into circuit

    Hi folks, DIYer here, hoping for some advice before most likely calling in a spark. I'm looking to wire in new cooker and hob (separate units). Max draw 3.5kW and 7kW respectively. I believe the circuit is radial from consumer unit (32A RCD) to 45A DP switch plus socket. Have done diversity...
  11. Q

    Switching and isolation for cooker and hob on same circuit

    Evening all, I'm upgrading my kitchen electrics replacing the current gas hob for an induction hob. The oven was previously plugged into the kitchen ring. My thoughts are that with diversity and the fact both the oven and hob are on 13amp plugs or rated at less than that, then they could go on...
  12. S

    Anyone know this cooker switch?

  13. HappyHippyDad

    Cooker RCBO trips when any other RCBO tested?

    I will start with apologies, as I have not thought this through very much (at all) yet and have just sat down with a beer.... meaning I thought I'd ask the collective. CU change today. I did my pre checks and I knew I had a major IR fault on the cooker circuit (N-E 0.3ohms, yes that figure is...
  14. E

    cooker element readings

    I have measured the following readings to earth on a twin oven---- Element 1... 0.149, Element 2... 0.9, Element 3... 0.88 , Element 4 0.08. These all with the merger set at 500v. they all seem low to me especially Element 4, needless to say the RCD trips randomly.
  15. brongochungus

    Cooker circuit tripping out with no appliances on it. Not immediately tripping.

    Even if the cooker and the plug is turned off it still trips after about an hour. It doesn't immediately trip out but it usually always turns back off after an hour or two, it doesn't immediately trip out. Do you think I need a new plug? Can a device plugged into another circuit trip a different...
  16. R

    Wiring up a new cooker hood motor

    Hi I am looking for some help. My Rangemaster cooker hood stopped working sometime ago, I’ve stripped the hood down and degreased the hood. Ive diagnosed the problem to be a faulty motor. I’ve bought a replacement motor, like for like, although the new motor has the same coloured wires but is...
  17. Justyjust

    UK What’s the chances me getting a 40amp cooker on this?

    I recently purchased a property not looking under the the stairs at the electrics, now I’ve had chance and thinking about getting a new board installed and fitting a 40amp electric cooker. I’m in doubts and unsure if it needs an upgraded cut out, the meter has a 1995 date on it. Smart meter...
  18. D

    UK No rcd on lights and cooker

    Can anyone help me with this I have a old plastic consumer unit with one rcd with lighting and cooker not on rcd The original lighting circuit has been altered over the years and 16 non fire rated spotlights put in the kitchen with all earths cut out 2 bathrooms 5 spotlights in each not iP...
  19. D

    New cooker chimney hood

    Good afternoon, Sorry for the long post but can find answers to my questions anywhere. I’m want to replace my old cooker hood for a new one. There is an fcu at the worktop level and T@E running behind the tiles into a round junction box above the extractor. The old extractor is just wired...
  20. S

    Electrical fault cooker

    Looking for some advice please. I have lived in my property for almost 7 years now. Since living here every 6 months my heating element blows in my fan oven. I have purchased 3 new cookers since living here all different models. Instead of replacing the oven I started getting the element fixed...
Best EV Chargers 2025
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Advert

TrueNAS JBOD Storage Server

UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
JBOD Forums: a forum for JBOD storage server advice
JBOD Suppliers: JBOD Storage Server Supplies
Back
Top