cooker | Page 5

cooker

Recent contents View information Top users
  1. B

    Cooker electrical fan replacement

    Hello, DIY enthusiast, but no real skills! Our fan oven stopped heating so I thought I would replace the heater element. When I have taken it apart, it looks as if part of the wiring may have come off. There is a clip on the right hand side with no wire coming from it. Will this be the issue...
  2. littlespark

    Would this be original? Cooker flex

    Disconnected a cooker ready for a kitchen to be removed, and found this. Freestanding cooker with 4 rings, oven and grill.. rated 11.3kW, supplied by what looks like 1.5mm flex. I know take diversity for cooking appliances, but 1.5 is pushing it a bit. Just wondered if this was original to the...
  3. V

    Can you have more than one socket on a cooker circuit ?

    I've been trying to locate anything in the regs that say this can't be done, but can't see anything. Basically I have a 3kw oven on a 4mm T&E cable going to a 32A MCB (Cable is clipped direct in loft to consumer board, and not covered by anything en-route - property is a bungalow). The isolator...
  4. jackhammerJIM

    oil fuel AGA cooker feeding unvented cyclinder gravity fed

    Hello lads . Not seen the job but my old buddy the plumber has informed me today he has replaced an old cylinder with an unvented . Alarm bells are ringing im going to ring the cylinder manufacturer on monday to clarify a few things but im concerned about achieving positive shut off . I...
  5. M

    UK RCD Fuse Box Keeps Tripping - Cooker Ring

    Hi, We have an old cooker on the mains with a cooker mains red switch with a normal plug next to it. The red switch is in the off position as is the plug switch. Whenever I reset the RCD for the cooker ring in the fuse box, the entire RCD trips again - even if the cooker's red switch on the...
  6. B

    Rangemaster Cooker

    Hi There, I've just discovered that my rangemaster dual fuel cooker is plugged into a socket under my kitchen unit with a 13amp plug. I've not had a problem with it until today. The cooker was installed when I purchased the house back in 2014. Today I was using both the grill and cooker as I...
  7. HappyHippyDad

    Cooker hood with heat exchange?

    The customer has asked for a cooker hood with some kind of heat exchange. I'm not entirely sure what he wants, but I'm guessing it's a cooker hood which reuses the hot air, i.e an MVHR. This is the only one I can find though and it's ridiculously expensive Lo-Carbon Sentinel Kinetic Cooker Hood...
  8. D

    Cooker cable

    Hi we are about to re do our kitchen and am looking for information on the hard wireing for the built in cooker as we want to move it! Can I buy new cable and lengthen the cable from the cooker to the wireing point and have the cable running around behind the cabinets? If not how much would it...
  9. L

    No cooker switch

    Hi All I had some new wiring put in professionally and I asked to wire ready for a cooker. He has left me a cable from the floor where I said it was going but no switch. When I went to buy a cooker with install included it said on the website they would only install it if there was a cooker...
  10. R

    Electric Cooker 4mm Vs 6MM

    Hi there. I’m looking for some professional advice. I recently bought Beko Cooker model KDC653S, it doesn’t come with the electricity cable and according to the manual it require H05W-FG 3X4mm or equivalent with total power consumption of 10KW. I called all local shops including electricity...
  11. H

    carbon filter on cooker hood

    I need to change the carbon filter on my cooker hood but I can't open the old one. I have tried Wd40 but it still won't budge. Model Lamona 2501
  12. I

    6mm cooker cable

    If this protected by a 40amp rcbo is this unacceptable. Does the cooker kw not effect rcbo size?
  13. I

    No continuity on cooker circuit.

    Not getting a continuity reading on the cooker circuit. I'm doing I.r. test and its low between l. N. Any ideas what the issue could be. The cooker sockets is working also.
  14. Z

    Swapping Cooker Control Unit for 13A Socket?

    I'm interested in powering my hi-fi system from a radial circuit in order to isolate it from other electrical devices and so improve sound quality. Unfortunately installing a new circuit is not feasible due to the age and construction of the property. What I'm thinking of doing is running 6mm...
  15. M

    Using pre installed cooker circuit for 13amp or 16amp oven.

    Hi all this is my first post. I am renewing my kitchen and at the moment I have a large cooker I'm changing it to a single oven. At the moment the cooker is on its own dedicated circuit with a 32mcb and 6mm cable going to a 45a cooker switch then going to a 45a cooker outlet plate which the...
  16. I

    4.5kw on 30a cooker

    Just installing this for a friend. 4.5kw ÷240. Minus 30% is that right.
  17. T

    Can i add a socket to my cooker control unit.

    Hi my father has just had a gas cooker installed. A free standing gas oven , gas grill and gas hob. The manufactures say that the ignition for the gas must be a 13amp plug. Is this correct? 13 amp for ignition seems to high . Can i down size the to 3amp and hardwire into 3amp fused spur. I have...
  18. N

    New cooker wiring

    Hi I'm looking to buy a new double oven and induction hob to replace my very old ones. The current units are both wired to an double pole cooker switch nearby and then on via 6mm cable, under the wooden floor to the consumer unit about 15 feet away and a 30 amp fuse. Having started looking at...
  19. S

    Main Ring / Cooker Ring Trip RCD

    Hey everyone help needed please. Moved into a new home, and have just had all the first fit installed for a new kitchen. During first fit, the electrician changed a socket on the kitchen ring and then moved onto another part. Within a few minutes the whole house tripped on the RCD. He retraced...
  20. T

    Cooker hood and bathroom fan connection via duel appliance outlet plate.

    I wish to install a bathroom extractot and cooker hood from an existing 32 amp 6mm cable . I intend to use a duel applliance outlet plate to split into two 6mm cables running to seperate 3amp FCU's from there 1mm cables to all parts that follow . See diagram . Is this in line withs regs. Thanks .

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top