I have the rad fan of my car set up so it can be switched on if in traffic-jam and the coolant temp starts rising
on the rad, the wire I can cut in to (easy option) is a negative feed and where I have the on/off switch there is a posative feed so I use a relay to swap the posative trigger in...
If you go and check the MCS012 database there are only 11 products currently registered. It will be 12 in the next 24 hours when Redtip appear on there.
Here is the rub. At Ecobuild those roof mounting companies exhibiting we're all confident they would be registered by 1st April. However, not...
4ft old style starter/ballast type fitting which when powered does nothing at all (not a flicker) but trips the 6A/30mA RCBO after maybe 3-5 secs. I didnt have my clamp meter with me when i went to see the fault but assume due to the time delay that its the overcurrent part of the RCBO rather...
Hi guys, Got a TT system. Do I need to install a time delay RCD on an old Wylex board that is supplying off-peak night storage heaters. The unrestricted board has been changed to 17th last year but the restricted board has not been changed.
Cheers. The external Ze is very good at 0.18.
Hell all,
I have bought and installed a LS400 Intruder Alarm. On testing I have found that when set in the Away Mode, and excluding entry/exit zone/route the following:
If the alarm is activated there is a 15 second delay before the internal sounder operates and a further 30 second delay...
At least for the low ohms measurement range anyway. It'd be great to be able to quickly set a delay period between the pressing of the Test button then the actual performance of the test, for those awkward tests where you can't hold the probes in place and press the Test button at the same time...
I've been asked to install 2 electric showers. That's the easy bit. The client has asked me if I can install a timer so they will only run for a maximum 10 minutes. Is this possible? The reason is to stop the kids spending hours in the shower and save on energy.
Hi guys,
Got job ...studio flat just done some odds and ends that requires i put new RCD CU in property.
Very small load currently being fed by T&E from OLD wylex MCB in cupboard on ground floor. Question is The cable of which i did not install
is run (from what i can see) under floor boards...
Is it me or does this say that the first lot of people to be signed up for Green Deal will be Jan 2013???? Government sets out next steps for Green Deal - Department of Energy and Climate Change isn't that a delay???
Hi all
Went to look at a job today on a farm , 3 phase board with 75mm supply on a 100 amp 100 ma rcd mainswitch, with a submains out to the house , which is also protected by another 100 ma rcd, problem is every time theirs a trip in the house it trips at the main distribution board also which...
Hi guys, i'm new here, and looks like noone asked this, but if i'm wrong, sorry..I need time delay contactor on ON and OFF, for lights on my house connected to my alarm, but idea is for them to go on minute after power is on and go off minute after power is off. Its over 2.2kw so i will use...
Hello All, I have just replaced an outside bulk head light for two PIR flood lights, looped from first light to second. All was fine, working as they should until the customer called me to tell me they were not working. Turned the breaker off and on for a quick check, sure enough not coming on...
Anyone know of a pneumatic timer switch with a 1 hour delay suitable for use with a wall mounted domestic/office heater? Everything I can find has a max of ten minutes or is designed for lighting circuits.
hi guys im an apprentice and need some more understanding about rcds
please may i have an example of rcd discrimination and what ratings i would use for different things and why
thanks danny
I've noticed on a couple of ocassions now.
That my Type s 100ma rcd will somtimes trip before either of my 30ma rcd. CAN some one tell me why this may happen?
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc