door

  1. uksparks

    PV Install next door.

    My neighbor is just having PV fitted as we speak, and I can see them with a disc cutter on the roof, they are cutting the tiles, they are just flat ones. When I had my ones put on, they didn't cut any and they say nice and flat as I watched the whole process. Seems a bit odd that they are...
  2. ses

    Wrt door entry system

    Hi Guys im not sure if this is the correct section, I have not been online for a while and can longer access the security section for some reason. i have a customer with a WRT cat 5 video door entry system. The door release part is no longer working. the door lock release i have tested with a...
  3. E

    Meter fixed to metal cabinet door

    I have been asked to do a partial rewire of a 1960s maisonette. The CU and meter are housed together in a metal cabinet. The CU is attached at the back but the meter is attached to the door rather than the back. The existing cables have exposed copper where they enter the meter, probably from...
  4. M

    Magnetic door sensor to turn on led light problem

    ok so what i am trying to do is. 12v led turns on when the door is open and turns off when the door is closed. But my sensor does it backwards " when the door is open the light turns off and when the door is closed the light turns on... on my tester it shows closed circuit when the magnets...
  5. albi

    door entry system unknown

    can any one help I have been asked to source some extra fobs for a door entry system but there is no manufactures name on the panel or inside so any help would be appreciated we have tried videx but that come back as not ours
  6. A

    Videx Door entry system help

    Hi everyone I've recently installed a door entry system in a customers flat and they're saying the latch release doesn't work properly. All the parts I have used are from 'videx' and from what i've heard they're the dogs ********. I have wired it so the visitor at the front door presses the...
  7. H

    Roller Shutter door connections?

    Hi I have been called to a job recently to install a up and down switch for a small roller shutter door. Motor and control unit all there but previous owner had ripped the switch out. So just left with a few cables not connected to anything and empty connections. I havent done a roller door...
  8. LauraADIA

    Legal requirements for Automatic Door engineers

    Hi all, I've just joined the forum as I think it's important to inform those who are electricians that are thinking about expanding into automatic door servicing and installation about certain regulations. If you are familiar with automatic doors, you will understand that they follow the...
  9. S

    Scantronic ion 16 door contact

    hey guys I've installed a scantronic ion16 alarm system a year ago been working fine. Now i want to add a door contact but for the life of me can't get it to work. I know it needs 2 zones but abit unsure on the jumper settings, 2 jumpers one for n/c n/o now I've set it to n/c and a reed jumper...
  10. T

    Can somebody recommend a door access with intercom product please?

    Alreet chaps. I look after a few offices near me and one of them wants to have a new intercom. I have done door access for the company i used to work for however i just had all of the materials provided for me. My sales guy at CEF has priced me up a couple of products that use cat5 with a PSU...
  11. driverman

    PVC Door alarm contacts

    Hi Guys, Burglar alarm question regarding fitting surface door contacts onto PVC doors. I've fitted a few surface standard everyday type contacts on timber doors and PVC doors before. The doors when in the closed position have been flush with the door frame. Therefor,the contacts are side by...
  12. G

    radio interference on door entry system

    Hi all. Got called to a door entry system fault. It's a new install but I suspect the guys who did it ran the cables with no consideration to segregate from mains cables. My jaw dropped when looking at the rest of their work. Anyway 9 appartments and an outdoor speech unit and all all handsets...
  13. A

    Help needed with door entry system

    Hi, I'm wondering if anyone can help with out with a door entry phone handset that is compatible with a telefusion system? I would like to replace the speaker/buzzer in a ground floor flat. I will include some pictures of the unit I would like to replace. The external unit I didn't get a...
  14. B

    Roller garage door problem

    My neighbour has a problem with his Securoglide Compact electric roller shutter door. When using either the wall mounted control box or remote control it closes OK without any problem but when attempting to raise it using either controls it stops after a few seconds and starts again...
  15. S

    Door entry question.

    Hello all, I have been asked to look at a job involving installing a intercom/door entry for a small commercial wharehouse/office At the moment they have metal/glass door like the ones on most high street shops (not automatic) open and closed by key I was going to put a coded panel in to...
  16. M

    Industrial roller shutter door help

    Hi guys iv got a indutrial roller shutter door at work which will only go up about 2 meters and stops in the same position everytime when you push the up but it will not go any higher but can be lowered n re hightened to the same position and cuts out. Does anybody have an idea what this could...
  17. driverman

    door entry / exit problem

    re my weekend project that I'm doing. I've first fixed for a burglar alarm system. Front of house is all glass including the door, so basically a normal door contact is a no no. In this situations would a beam in the hallway be possible? The idea being as and when front door opens inwards it...
  18. sythai

    Door entry alert/ door contacts

    Morning All Fitted for a customer a while back a door entry alert with laser beam detection. Cost well over £100, but has now failed. Not an off the shelf item at wholesaler so bit of a pain to take back/ spare parts etc. Want to replace with a lower cost option, that would be easy to...
  19. M

    Led door sills

    Hi......I have just had delivered 4 sills/scuff plates Which have leds in all 4. I also have a separate cable with 4 plugs on it which obviously connect to the 4 sill plates. My question is where do I wire the end of cable too......I presume the drivers footwell lights? Is so what wire goes...
  20. R

    troubleshooting digital door entry system

    hi forum, i am new to this site and this is my first question i am seeking advice on troubleshooting problems on a ISM C2000 digital door entry system are they any members, who have worked on this system or similar, who can offer any practical information or troubleshooting tips having read...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

Daily, weekly or monthly email

Advert

Back
Top