I've got a CDA ECP62SS/2 extractor fan, can anybody tell me how to remove the lights so I can change the bulb. Also what type of bulb is used in this model.
Thank you
Hi all,
I read through the post that dealt with using 12V LED bulbs in place of incandescent bulbs but my issue is a little different from that thread.
I will be checking out a ceiling fan that has 4 lights on it. The owner said he replaced all 4 incandescent 120VAC bulbs that were working with...
Does it make a difference?
My FILs bathroom fan had stopped working, and after checking power was where it needs to be, conclusion is fan is faulty
“I could have told you that… it doesn’t work!”
The fan isn’t too old, and I’m wondering if the way it’s been mounted is causing too much strain...
Hi all,
I'm looking for recommendations for a kitchen extractor fan i.e. rate of 60l/s.
We're almost finished renovating and we've just been told we have to have one (I know bit late in the day and I'm not happy but we are where we are). There are only a couple of spaces for one to be located...
New construction in USA. I think that the builder put ceiling fan rated boxes in the ceiling. But when I remove the cover, I see a strange box. Picture attached. It's hard to make out all of the details, because the painter sprayed it.
Have you seen this brand/style box before?
There are two...
The switched connection unit for the kitchen extractor fan and the lower part of fan is now behind a larger fridge, so the fan can't be operated without climbing onto a worktop.
I would like to replace the fan with a Manrose LP150STC, which has terminals for a switch on the live line, and bring...
I have an envirovent fan that I'm replacing that is connected to its own switch (ie not the light) . The current wiring has a live and neutral. The SIL100T model seems to have Live AND Live Switched and Neutral. As I only have the two wires can I just use a short piece of wire (from an old plug...
I'm not an electrician, but I do electrical tasks for my employer. Hello underfunded maintenance department.
I'm currently troubleshooting an exhaust ventilation fan system that's powered via a contactor, with vent louvers (the things that open/close to seal the vent or unseal it) that...
Not specifically electrical, but best way to minimise condensation in a shower room. Asking for a customer.
Background.
Customer is a neighbour. Previous owners of house had broken through between a downstairs WC and a large cupboard and fitted in a shower cubicle.
There is an existing 4”...
The above car is on its third fresh air blower resistor pack, (2 replacements), the fan impeller spins easily by hand, the (4 speed) fan will only run on full speed (4) when the resistor pack "burns out" presumably. the resistor pack is cooled by the fan air flow, and measures ~ 42mmX32mmX10mm...
Hi. Has anyone tried the Atoko Fan Select (ATQ6-03)? Its supposed to be an extractor fan timer so you can get delayed start and run-on using a standard fan. They say you can also override the delay and run-on by switching the light - does that really work?
I have an old Baumatic oven that hyas been tripping out my new fuseboard . I removed my old element ..photographed the wire connections..or so I thought , only to find out that the only wire connection I can see is the earther ( yellow green) in the middle . the other wires are brown...
Hi all,
I've recently replaced my 4 inch centrifugal extractor fan fitting in the loft. I was hoping for some advice on if this is wired up corrrectly. The fan itself is working well.
Old fan had timer, new fan doesn't have timer.
Both fans are turned of via the pull switch in the bathroom.
I...
Hi my 4 inch centrifugal extractor fan in the loft has stopped working.
Looking at doing a like for like replacement, but am confused with existing wiring vs wiring on the new unit and where the current wires would fit into the new unit.
I've attached the current wiring set up for the broken...
My very well off customer wants the most quiet ceiling mounted extractor fan there is. They have stipulated that cost is not a barrier and they just want something quiet.
I have used one extremely quiet fan in the past, but it simply didn't do it's job, so that's pointless. This fan still needs...
Hello,
DIY homeowner here in South Carolina. I have a question regarding wiring some lights and a fan.
I’m replacing an old ceiling fan. It has 14/3 running to the box. The old fan has 3 switches wired. One controlling the fan and two more controlling the lights on the fan.
I’d like to add...
Backstory:
Installing a new ceiling fan in a 45 y.o. house, rewiring to an existing switch. The leg was for a switched outlet, which was wired in a peculiar way - on a 14/2 copper, both leads are hot (no neutral). I haven’t opened the sheetrock at the baseboard to see where they wired the...
Hi, I need to replace an old extractor fan in a house I rent out. The bathroom has a lot of black mould on the ceiling and I'm wanting to prevent this from happening again. A fan with a humidistat that turns on when it gets too humid sounds like a good idea but is it as easy as just replacing...
I currently have 2 3-way switches controlling a light fixture in a room in my home. They are wired like the attached diagram. I recently purchased a ceiling fan for the room and I’m wondering if I’ll be able to use the required ceiling fan switch in place of one of the 3 way switches? Thanks!
Just had a call from an M&E client of mine and good mate asking to pick my brains.... large 3ph biomass boiler with (I assume variable speed) 1ph fans internally. Says he's got 230v L-N/E on the connecting plug but when the fan gets connected there's nothing on the internal fan connections...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc