I have been asked to fit a set of electric gates and some garden lighting to a property. I'm working behind the guy doing the indoor electrics. He is talking about me wiring the gates back to a plug and the garden lighting to a fused spur. Question is do I issue a minor works certificate for...
Hi
I'd like to swap a 13a fused spur for a single 13a socket as we're never going to put a fireplace in and just want to have less wire clutter.
I've swapped sockets over before without an issue but what's confused me here is that there are 2 sets of wires going into the socket (see picture)...
like unicorns, I have seen pictures of these, but cant seem to find a distributor.
can anyone assist ?
at present there is a double socket in place with limited space around it so looking for a combined unit.
I know I can change the back box and put two single units in its place, but saw a few...
Hi,
I am trying to find a fused spur that is as small as possible. I'm not sure of the correct wording but it needs to be smaller than a single gang back box.
To explain what i am trying to achieve, i need to cut the plug off a flex that connects to a small transformer for an POE injector. As...
Hi - I'm planning to fit an extractor with timer to a bathroom, switching on with the lights and had bought a fan isolator switch, but reading the Manrose instructions they insist on double pole fused spur with 3A fuse.
I think it will be easiest to fit a switched fuse spur and not bother with...
I am planning a new layout for our utility room and would appreciate some advice. We have three appliances (washer, dryer and freezer) that will sit under a worktop directly below the window. My intention is to feed this equipment via a row of three 13A fused spur switchplates located inside a...
hello I've seen the page at the back of the regs book but nothing explains can you -
Have a spured socket off the ring using one cable and then put a fused spur after the spur and then feed additional sockets after the spir
Hi,
Had a problem recently. Switch fused spur fed off ring main to control 6 x t8 5ft fluorescent tubes works when it wants, tried replacing fuses and tried a new spur, and keep getting the same problem. Its not overloading and havnt come across this before.
Any ideas??
Thanks
I wanted to know if a radial circuit that has a fused spur at the end of the circuit can then feed a double socket if I use a 13amp fuse in the fused spur? Also would that then have enough power to run a washer and maybe a chimney hood fan above a cooker hob?
Before I start, I know this is not usual but I want to know if it's against regs.
I'm testing a conservatory ring, feed from a fused spur. There's a Live-Neutral IR fault between two of the three sockets.
The cable is embedded in the conservatory bare block wall.
If I just disconnect the faulty...
Query regarding a Passive RCD fused spur unit protecting a bank of 4 led downlights supplied via switched live and nuetral. I have been asked to replace the downlights. Cant be totally sure but i think RCD spur was to protect the (addition)of the downlights. The rcd is passive so will remain...
Hello, need to run a supply to a tyre air line at a petrol station. No info on it but think its probably around a kilowatt, definitely not over 3kw.
Should probably be on its own dedicated circuit, but going to cost more.
There is a socket inside that I could spur off and save alot of extra...
I need to work on a board with no RCD protection. Rewiring kitchen lighting and adding downlights. Is it acceptable to install a 30mA RCD spur unit at the consumer unit, feed the spur direct from the MCB, fuse the load side at 13A (Leaving the 5A MCB protecting the circuit) and use this for the...
Hi guys,
whats the regs regarding fused spurs?
Is it ok to have, from the ring main, a fcu, feeding another fcu, feeding another fcu etc or is it only one fcu per socket like a normal spur?
I've got a fcu spur from the ring main for a fan in the bathroom. I need to fit in an electric...
i was at work today replacing some sockets and backboxes and there was 2 fused spurs im a 1st year apprentice... i dropped the faceplates put the new backboxes in etc... and there was a linking cable for the 2 fused spurs and i linked the supply and the actual linking cable together in the...
Jake1579
Thread
advice
cable
current
fuse
fusedfusedspur
overload
spur
wiring
Trying to calculate the voltage drop for a run on external lights supplied via 5Amp Fused/rcd spur from local ring final circuit. for a quotation and have got a bit confused re Voltage drop.
27m run in 1.5mm cable total load on lighting radial 420w. (no diversity as all lights either on or...
Situation.
Garage being converted into office.
No spare ways in CU. RCD protected circuits, 2 x Radial 32A in 4mm T+E, 2 x Ring 32A in 2.5mm.
The garage currently has 1 x 2 gang socket spured from one of the Rings.
The customer requires 3 x 2 Gang sockets in the new office.
My question is...
Hi
Ive been searching everywhere to confirm with regulations that you are able to install a fused spur outlet off the downstairs ring for an electric fire (which is only to be used for the flame effect it provides not for heating as have central heating) and a LED Driver for a strip light...
Ive carried out an Electrical condition report recently and found that the main switched fuse isolator for the installation has control wires running through it from a control unit mounted above the isolator to contactors mounted below the isolator. The control wires are 230V. Im sure ive read...
rawlins1463
Thread
control
fuse
fusedfusedspurspur
switch
switched
used
wiring
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc