I recently had CCTV installed and the contractor installed a plug socket in my loft, spurred from the lighting circuit - which is unearthed. He added a four-plug extension lead to take the plugs for the four cameras. Is this safe? Or should I be concerned? Many thanks for any advice and help.
Karen
New Member and wannabe electrician. I'm teaching myself for now for obvious reasons.
My problem is an extension light circuit and the conundrum is:
The circuit will only work / operate from the main circuit breaker. As soon as I wire a switch into the circuit it will not stay on and...
Hi gents,
I am going to a job to install some new external lighting on a factory on Monday. There are 5 new circuits to run in total. They want these to be controlled by a time clock an photo cell but also run through a key switch and contactor. It’s been some time since I wired contactors and...
Hi,
I'm fitting a new lighting circuit into my garage consumer unit that will feed 2x outside wall lights.
I plan on using a two way circuit to have an external switch and one located inside the house.
The attached picture is how i plan on wiring but i have one question about the Neutral feed...
Hi got AM2 in a few weeks, on the build there’s a 2 way and intermediate to wire up, I know how to wire one up but the way they want it doing is not the way I have ever done or the way I would do it, you need a neutral at every switch, from DB to first switch in T+E then 3 core to intermediate...
OK, lets have a decent discussion about this as I'm sure there will be a number of opinions!
Have done an EICR on a 40 + year old flat. The lighting circuit is wired in singles and utilises the steel conduit as the CPC. Out of the 6 lights and using my R2 wander lead, only 2 have an acceptable...
Hi just thought I'd throw this out here for a bit of light entertainment after the @Marvo thread (phew!)
So brother in law asked me to look at EICR which returned unsatisfactory. I have not looked at the installation to ascertain as to Class 1 or 2 fittings in the premises are installed. The...
Hi,
I was doing my r1+r2 tests on a lighting circuit yesterday in a 6 bed house over 3 floors. Approximately 20 points not including switches. Mainly pendants but some light bars etc and almost all LED or low energy halogen type bulbs. Closed circuit r1+r2 values range from 0.88 on ground...
To my knowledge, there are 3 methods of splitting the line conductor in each lighting circuit:
Joint box below floor, or above ceiling
Three terminal ceiling rose/batten lampholder
Joint in switch box (neutral)
I am wondering which method is most commonly used in new houses.
I have been in...
If someone has run a 2.5mm lighting circuit spurred from a ring final on a B16 breaker, I am assuming there is no need to have a fused spur where the lighting circuit comes off the ring final?
i installed a new CU yesterday. During testing I noticed 15-30v on the 2-way lights circuits while off. I traced this back to cables being run together and caused by inductance. I can't separate the cables.
Should I worry about this, anything I can do?
Thanks,
Michael
my eldest son has autism and learning disabilities. One of his behaviours is messing around with lights - either switching them on and off rapidly for a few seconds or going around switching on all the lights in the middle of the day.
Yes, we could go into the kitchen cupboard and use the mcb...
Hi all,
I am rewiring the lighting circuit in an old pub. It wasn't until running the new cable that I discovered the circuit branched off to a porch light through a junction box under the floorboards. This is where the circuit originally shorted out. I've completed the rest of the circuit and...
Hello,
New builder and Electrician started today to wire-in electric shower to wire already in place for it.
They phoned to say that the new consumer unit that old builder's Electrician put in, which is a 10-way, has no spare way for the shower cable which wasn't wired in.
I spoke to old...
Hi all,
Strange one today that i've never seen before - hoping someone else may have seen this...
Wiring an additional outside bulkhead today - couldn't easily get to the last fitting to take a switch wire from there so split the switch wire as close as i could to the fitting and wired in a...
Hi Guys
Help! The 6 amp MCB for a downstairs lighting circuit keeps tripping, sometimes instantly, sometimes slowly. An IR check live to earth gives >200 Meg on the 250 Volt range (I don't want to blow up the dimmers!) when all light switches are OFF! This reduces to near short circuit when you...
Evening,
I am rewiring my house and would like to put spotlights (around 10) in my kitchen. I was thinking loop in at the switch (from previous rose and to rose in next room) and then run the t&e cable (l,n & cpc) from one spot to the next to the next. Is this correct?
(Usual caveat- I'm still...
Hello. I'm just looking for a bit of advice.
I had a new boiler fitted a few months ago. An electrician came and wired it up and left me a Minor Electrical Installation Works certificate.
ive just had a plumber round to check the work and he says the electrician has wired the boiler from the...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc