Hi everyone I hope that you are all well and enjoying your weekend. I have a Megger Pat3 tester which I inherited from my dad. I now want to get it calibrated and start using it! The problem is, I don't have the user manual for it. The basic instructions are printed under the lid but I would...
I want to run a switch from my fan to the inside of my car. The fan works when I connect both wires to the battery but some of the wiring is missing because an engine conversion.
Do I need a relay between the fan and battery or fuse or what?
Hello, boilers and thermostats are not my strong point. Can do following the manual, but unfortunately Hive model is not mentioned in the boiler manual...
Been doing new electrics for a kitchen refurb, customer brought this new thing and I got a bit stuck on it.
Got some pictures from both...
My first post so I hope I get this right!
i have just fitted a Honeywell Accenta mini gen4 with lcd remote keypad for my dad. All seemed to go fine until I tested the system. The initial power up was as the manual suggests and the LCD keypad read "system unset". I then entered P and the...
Hi , I am a newbie trainee and would like to understand something please. I am working with someone else, replacing outside pir lighting. The property has 3 outside lights front, and 3 at the rear. They are currently the half lantern style PIR slave units. the front ones have a manual...
Hi, I've just moved into a 1900 house with an existing home alarm. It says on the box that it's a Gemini Advanced Microprocessor Control. I don't have the manual but would like to change the code. The previous owners didn't know the code either.
Is there an online manual or a way of changing...
Apologies if this has been asked before (I'm sure it has - I just can't find the answers).
I would like a complete wiring diagram for a Ford Transit 2005 - model 85 T260 (SWB, 2L diesel).
I have been Googling but got nowhere.
Cheers!
I've just popped over from the other side, ( plumbers forum ), to ask if the above mentioned room stat is a type of intelligent stat, in other words can it be taught to know how long the system it's controlling takes to reach its preset temp, and to come on before it gets too low, ( hopefully...
Have a M-Ecodan ASHP system installed by a firm that's now parted company from the builders, so no warranty backup, and the ball's landed in my court to pick up the mess (six installs, btw).
I've just done a callout to a non-working system which is flashing up an E9 code both at the tank end...
Hi guys I have a texecom veritas alarm I installed about a year ago, I'm wanting to move the bell box outside to a different wall but Im not sure how to bypass the tamper on the bell box so it doesn't bell up when I take the lid off, any ideas or help would be great!
Hi, Could you please give me some advice - I have the veritas 8 alarm with keypad and today I had to turn the mains off to do some diy work. When I turned it off within 2 minutes the alarm started beeping and the alarm went off inside and outside the house. I tried to reset it but it wasn’t...
Hey Guys,
I purchased a fluke 1652 and am waiting on delivery, I need it for a lot of things but one feature I need and am not sure if it has it is the volt drop feature on some flukes.
When you test a battery on start up or a generator for example some flukes will let you hold a V min (too...
Hi all...been away for some time and now medically retired due to 2 strokes and losing my sight :-(
Can anyone supply a li to avers install manual? ts for my father inlaw who needs to reboot hi panel and I cant find one anywhere...
Thaks guys... :-)
Hi I have just installed a Optima G4 panel and connected up to a remote Keypad. The alarm works ok however the RKP is displaying the "System Optima G4, Software installed and Build number". I guess l have to activate this. How do you enable the Remote key pad (RKP) from the panel or get this...
Does anyone know of any good software for android devices? Need to be able to input details of company and logos etc. Either free or as cheap as poss.
Also I've had a look on eBay for barcode scanners, they are pretty expensive in comparison to USB and wireless barcode scanners. Does anyone...
Good Evening Lads
Been out of the game for a while, I have a 1553, can someone please explain the lead positions and the correct test procedures.
Many Thanks
Chris
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc