As above does anybody have a copy of a manual for an Electra tech control panel? If you have and you would be willing to email me a copy it would be greatly appreciated :)
You know the story, new house, alarm and zero information even regarding the installer although I do know the user code. The problem seems to be the programming, works OK on Part but not on Full, battery in unit is holding charge, sounder battery not checked yet.
Can anyone identify the model...
Hello all.
I've been asked by a client to convert a pull-bell doorbell system (pulleys etc) into an electric one.
When the 'puller' by the front door gets pulled, the rod (below) goes out. I thought I'd have something there closing a circuit.
When the circuit is closed, I was thinking of...
Hi guys,
I'm hoping this isn't something which has been covered millions of times before (I have tried searching) but...
I'm looking for a PAT tester with the full range of testing features:
-Earth bond at 25A (plus ideally a range of lower currents including 200mA for sensitive equipment)...
Hi,
I've recently bought a dual fuel cooker which requires hardwiring.
The user manual states that it needs to be connected to a double pole control unit with a minimum rating of 32A. However, i've just had an electrician round who, after looking in the manual, said that the oven only needs 8A...
I am in the middle of a series of eicr for a car dealership there's about 9 branches to do
in one of the branches they turn off the lights in the workshops every day with the mcbs as there are no light switches
now for one thing the markings on the mcbs have worn off so I'm unable to verify...
I have a customer with 16 panels and an SMA 4000TL who has asked the question: Can I put another 8 panels up on a different aspect and run them through a timed change over switch that will disconnect/reconnect 1 set of 8. Basically at any one time there 24 panels on the roof of which 16 are...
hi
can anyone help i am putting in a electric gate opener its a bft rigel 5 with p7 ram got it in but when i push the remote the display says stre then displays er16 can anyone tell me what the fault code er16 is and how to clear it
many thanks
Hi Guys,
Anyone have or know where I can get a hold of a copy of the manual for an Accenta 8 Mini Alarm Panel, preety old system so im finidng it difficult to get a hold of the paperwork. I have received two seperate calls this week about faults on these panels one of which is fairly baffling...
Been to a job in a poultry unit and there are some moller PKZM manual motor starters connected to 3 phase busbar in a consumer unit, not sen it done like this before. This is in a sub board supplied by a C32 TP mcb. Is this technically to regs? Do these starters cover short circuit as well as...
Hi Folks.
First post for a while. I've got a timer over-run extractor fan to fit for a customer as requested, but he's now asking for a manually controlled one. Apart from taking it back to the supplier ......... Is there any reason why I can't just leave out the permanent live, and it will...
Heys guys.
After a bit of advice regarding off peak heating really.
I recently helped my brother with his flat that he bought and done a complete strip out and re-new everything!
Before we got in there, there was just one storage heater in the lounge. He asked for one in each room, obviously...
Hi i was called to a job today where a previous electrician had been doing work in a kitchen but hasn't came back. The problem is there is a extractor fan above the cooker which has power to the socket and then power from plug to the mains in to the circuit board but the lamp isnt coming on and...
Hi helpers
I have just purchased a fluke 1653b tester. Having a play with it tonight ( the tester ha ha ) and I am having trouble with testing zs. I plug the 3 leads into the tester , plug the socket tester in and press test and get a reading of <2000 . I have not got a manual and I have googled...
Hi I am about to add 3 manual call points to an existing fire panel as it does not have them already installed to a block of flats as system ok but my question is what certification do I issue as it is only minor but there is no original certification at premises help thanks
Does any one have a manual for this meter? I can only find a sales brochure type pdf that says its wonderful!
I am interested in the 2 peak demand readings it displays. Can these be cleared manually.
Naturally we cannot reprogram it as its property of the ESB ( 'leccy board in Ireland ) but...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc