I need an outside light which comes on with a pir and when the customer wants the light on he can switch it on thus over riding the pir so it stays on. Can you buy it like this or does it have to be wired skipping the pir? Im thinking of a luminaire with the pir built in.
Cheers
Customer asked me to install some lights down their side access to the garden, it's pitch black as there is no street lighting nearby.
They have chosen some half lantern types with low energy flourscent type bulbs.
I installed it last week and now one of the neighbours are complaining about the...
Hi, i have been asked to install an outside light to a property, the customer just wants to plug it into a socket inside house - cable from socket to light will go straight through wall.
The fuse board is the old re-wireable semi enclosed (BS3036). Does the outside light need rcd protection to...
Right so i spoke to my merchants "How much for a 50W LED outside light" reply was £130 inc VAT... WTF
I now looked on eBay and found this.. 10W/30W/50W LED SMD Floodlights Day/Warm White Waterproof IP65 Outdoor Garden UK | eBay
50 Quid...? Anyone fitted one from ebay they any good?
Hi all, advice please....
I have fitted an outside sensor light.( Domestic.) it is less than one meter to the consumer unit. i have used 1.5 twin plus e from the back of the light connected to a five amp fused switched spur socket with a neon indicator then 1.5 again direct into the consumer...
I'm quoting to install an outside light at some distance from the nearest building.
About 16m of the run will be underground, mostly under lawn, with about 2m of that under paving slabs, which will have to be lifted and re-laid. I am proposing a 500mm deep trench with ducting and warning tape...
Physically doing it and wiring it I have no issue with and Zs, Vdrop etc are all fine. However I need a bit of clarification.
We live in a timber framed house, brick outside, dry lined inside. I’d run the cable from light fitting #1 back in the house, up the wall vertically from the switch...
A collegue at work has asked about having a PIR light added. Not sure if im allowed to do it but said that i would have a look into it. The Consumer unit has no RCD and is the old wylex unit that is found in so many authority houses (meteral i think / skelton type)
my thoughts would be to take...
Hi guys,
ive been asked to instal an outside light to stop foxes gettin into the chicken coup.
what sort of light would work best to keep away foxes at night? I've been looking at most motion sensor lights but im not sure if they are applicable to foxes
Can anyone please clarify or point me in...
does anyone know if there are outside lights available with integral PIR that you can over ride with a switch rather than doing that quick on/ off thing with the supply?
i need a light to illuminate a farm yard, i will be mounted on a shed approx 10M up, and needs to illuminate approx 300M² of yard.
there was a sodium lamp there, but it was poor quality, the plastic went brittle over 2 years and cracked where it mounts(probably from catcing the wind) and then...
Hi the client has a 6A light circuit already installed to supply an outside light attached to the wall. However, the CCU is 2007 and the circuit does not have and RCD protection. A fews questions sprung to mind.
1) The light fitting would be attached to the house and fed from the existing...
ok for my girlfriends uncle i was doin an outside light, all it needed was a light and was already wired, he showed me where it was switched from, which was off a 3g switch, so turned it off and test the cable to make sure it was that one anyway, but it was still live, so i took the switch apart...
Morning Guys,
Ive done a Zs test on an outside light which is on its own circuit and am getting a reading of 35.8 ohms on no trip mode. Im using a fluke 1653 multimeter which im new to.
In the bottom of the display below the Zs reading, its displaying Ik 7A. My Ze is 75.4 ohms.
Am I correct...
HI was wandering what cert you would issue for installing outside lights. Power is already in place. any may want to add some swa to it to extend? cheers
Hi people,
If I spur of the ring main to a switched fused spur to supply an outside 500watt floodlight, when doing IR test do I just IR the cable I have put in (from socket to light)? Or the full ring?
Thankyou
i have an outside light which goes into the driveway, they are like big downlights which sit flush.
The light sometimes works and other times when you put the switch on the "on" position it doesnt
it has a cdm-t 35w lamp which is new.
other components are an ignitor, a capacitor and a...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc