I need to run an outside armoured cable to a pond pump. I will install all the necessary protection devices. MY question is can the cable be laid loose on the ground between trees or attached to the trees. I dont really want to dig a trench all the way over a 40metre run. Thanks
I've been asked to 'remove the light cable over the front door' so as I was passing I decided to take a quick look before contacting the tenants.
Picture is taken from the path, the head, meter and CU are in the storm porch outside what is now the front door. Presumably the cable I'm to remove...
Hi there ,
Some advice about running power from the house to a covered way , obviously slightly different to a shed as it’s more open to the elements. Is it best to get a unit/cupboard for the CU ? Or not have a CU at all outside and place a switched spur on the inside wall to power them ...
Hey guys .. I'm running a new circuit to a large outside area in a garden , consisting of 5 heat lamps 250w each ...
I've done the calcs and it will.be pulling 5a . Cable run is only 15m
Are there regs on outside heater lamps in the 18th ?
And
Would 2.5 armoured on a 6amp MCB be ok ...
Hi
I've recently moved into a new property & have the following issue.
There's an outside light at the back & I can't find the on/off switch for it. There's power to it, as the light comes on if the sensor is tripped, but I want to change it to a normal floodlight & only have it on when I...
Hi all, have a job doing some garden lights. Want to use flexible conduit as I can fix to a wall that is then being battened out so no need for armoured. I would normally use black .75 pond flex for this sort of job but can only find it in 3 core and need 4 cores. Whats the opinion of using...
I needed to move a socket and to do so had to crawl in my loft, there are wires all over the place (not a clip in sight) and 3 junction boxes all right near each other.
Anyway what the hell is going on with this particular box?
Friend of mine has an existing extractor in the bathroom which is switch powered. He wants to disconnect it as it's never used, and feed a cable from the existing extractor feed through the exterior wall and into a PIR exterior light.
He's insisting that regular 1.5mm pvc is fine (i've said it...
I wish to install two outside lights & pick up the supply from the existing hall light switch. The hall light switch is a 2 way switch with red wires connected to L2 & COM & black to L1. Is it possible to replace the single switch with a double switch & use a live feed to operate the outside lights?
HI All
Need some advice. I had an electrician professionally install power to my garage. Here is how he did it.
Spurred off a socket on the ring main to a 13A fused switch. Then through the wall to a water proof junction box on other side of wall. Then waterproof cable along fence into garage...
Outdoor lighting circuit (domestic) without 30mA RCD additional protection, what code would you give it?
I'm leaning toward C2 as (A) outside lights have a habit of filling up with water, and (B) anyone touching it may be in contact with the bare ground.
What are your thoughts?
Anyone know of any good LED outside light's which last longer than 2 year's? They seem to all be garbage.
Getting so many customer's coming back after a few month's even. I generally go for a pre-wired LED fitting
security light (with/without PIR) with a IP rated box behind .I always assumed...
Hi,
I'm located in the UK and replacing my outside double socket plugs with ener-j smart wifi sockets. I've wired it as the picture below, exactly the same as the old one. I used my tester and it's only earthing one plug. There's another earth socket but I didn't need an earth wire in each one...
i have a spare 10mm cable under my kitchen cabinets which i ran in ages ago intending to use it for power outside, however i changed my mind and used 16mm instead. so was thinking of putting all appliances on 10mm radial with fcu's.
can anyone think why this would be a bad idea ?
cheers
Anyone used them wagobox capsules for swa Cables?
I’ve got an external lighting job with semi hidden joints wanted and the capsule top flush with the grass.
I need to plug two 12v 120w DC fans into AC 120v house plug. The wall worts i have tried don't work. What is the best solution, outside high humidity, green house?
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc