Can someone offer some advice please?
I would like to remove an old outside light fitting on a switch, currently wired as attached photo:
home - outside light
blue - blue
yellow/green - yellow/green
blue with brown sleeve - brown
three brown wires from home into their own terminal with no...
Hi,
I have removed a canopy from above my front door in preparation for a new door and glass panel being fitted. I’ve come across some very poor electrical work which I’ll need to tidy up. But to cut a long story short. The cable before to the outside light was run in the canopy then dropped...
Hi, I have a 3 headed victorian light for my garden, looks quite an old 1 in my opinion due to the colour of the conductor cables. Can anyone tell me please how to wire this up so it comes on. Does this light work of a switch, or can I put a plug on the end of this, I have an outdoor power...
Hi chaps
How would you best mount or connect into this light? It seems like it would be back entry but my cables would be coming from conduit or armoured from side. I know it's a pretty stupid question but what is neatest method
Got a customer who's wanting a washing machine and tumble dryer in the bathroom.
Normally the solution is to hard wire into FSUs but he's come up with the solution of kitchen units and a work top with the sockets in the void between the wall and the back of the units.
Could this be argued to...
Hi, have some outside up lights to do (for a mate) currently has just run 1.5mm SWA come to look at the up light what would best way to connect it be? It has a pot to then you screw your light into but on drawing looks like I need adaptable box then some flex to light? I’ll post a similar up...
Hi looking for some advice, looking to put some outside heaters (in my garden) 2 x 2500w, now I want a time delay switch but this can only switch 16A, so I’m looking at putting a contactor in as I already have one, but I’ve only ever used contactors twice before, is this the best way to set up...
That was the phone call... realism was that mr customer had tried to change his light switches and got a little mixed up.
Forgive the ms paint circuit drawing...
In truth, the outside light was the only thing that did work.... except it turned the rest of the house on and off as well!
The...
Hi
I'm replacing a PIR outside light with a new Dusk till Dawn light but have wiring questions. The new light has 2 connections, i.e. blue(neutral) and brown(live) but no earth. As can be seen in my image, for the existing light, there are 3 wires so I think the wires go:
1) black(old) goes to...
Hi, excuse the ignorance here but I am currently replacing an existing switch with a 2 gang to wire up a new outside light. The current switch has a live, neutral and earth feed as does the new outside light. How/can I wire this correctly? I presume I should bridge between the COM port but how...
Outside lighting, any suggestions on how to do this, only space I can get any cables from is the loft, now custard wants up/down lights, but low enough to be able to light up the wall, looking at half way? I can get one cable down to each light looking at 3 lights and do a joint box in the loft...
Good afternoon all,
I’ve got to fit 2x 20w LED Floodlights this week and just wanted a sanity check before I start.
There’s one light up already supplied from the upstairs RFC via a double pole SFCU. Supply goes out into the back of a wiska box which the pre-installed flex of the light glands...
Hi
I have a switch by my front door inside the house that switches on and off an outside light.
the front of the house has a lower roof that goes up and after windows joins the top roof.
therefore, I have an eves? That is about a foot above the top of the front door.
looking to place some Xmas...
I am looking to join 2 cables for an outside security light. The mains cable on the existing light is 8mm flat twin. But the new light is a 6mm round twin.
I can't rewire as it goes into the wall to the socket. So was looking at an ip66 connection. But can't find one that does both sizes.
Any...
Afternoon
i have changed hallway light double switch to a triple so I can add an outside light.
i have wired first switch for hallway
second switch is for landing which works both ways upstairs and down
so both work as normal.
so I have a third switch I would like to use as outside light but...
Hi All,
I was wondering if anyone could help me with a recent problem I’ve had on a job. About 5 months ago I installed about 5 outdoor soffit lights from switch inside. All worked perfectly and customer was happy. I’ve recently been called back to the job as the outdoor lights have been...
Hi all,
I have a job booked to fit outside socket which will be used to power portable hot tub. The socket will be waterproof fed from existing circuit via fused spur which I also going to fit. RCD protected at the fuse board (hot tub has got its own RCD device rated at 10mA)
The question I...
I have 1 external light in my garden and would like to install 5 more, what’s steps would I need to take to do this? Could I spur off my existing light? Would I need junction boxes for each light?
Hi. This may have been asked over and over again but just looking for a straight answer if there is one.
So my plan, install 2 lights near my front door. Am pretty confident with house electrics and did a college course some years ago on the basics so my idea is.
Convert a single socket to a RCD...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc