panel

  1. R

    Need to add neutral slots to my 125 amp panel to match ground slots.

    I have an Eaton 125 amp panel with a ground bus bar with 24 slots and 14 neutral slots. I have a 6 breaker Reliance 7500w transfer panel connected to it. The main panel has 4 unused breakers. I need to increase slots on my neutral side. Can I add an additional neutral busbar to the existing one?
    • Robert B
    • Thread
    • added amount amp breakers busbar ground increase neutral panel screwfix
    • Replies: 3
    • Forum: UK Electrical Forum
  2. V

    Eaton BR panel: what are these brackets for?

    I noticed some brackets along the sides of two breakers in an Eaton BR panel board. One is along one side of a 20A Type BR Combination AFCI breaker (labeled for the dishwasher and disposal), and the other along one side of a double 40A breaker (for the Range). They look somewhat similar to a BR...
  3. F

    EICR, Sub Mains from Panel Board

    My guvnor recons that all submains from the main Distribution Panel, should go via metered supplies. Although they are all for one customer who owns the building. Any reg on this, as I would like to look it up! Whether BS7671 or a Building reg.
  4. UKMeterman

    Poorly ten year old 10 panel installtion poor output in the afternoon

    Hi, This is a 10 year old 10 panel installation, recently output has been droping and somtines reaching zero mid afternoon. I think it is a sunnyboy inverter. Does it look like a panel, inverter or high mains volts? Could I have names of installers in West Yorkshire who may be able to help. Thanks
  5. S

    Solar panel kit for sale

    Hi guys. Unfortunately due to the coronvirus the the house I was going to be building is now on hold. Due to this the solar panels I previously bought are now for sale. I purchased this from the wholesalers for £1600 and am open to offers. Its all brand new still in boxes. Included are: 8 X...
  6. J

    3Ph supply to sub panel

    Hello all, after some advice please. I have got a small job installing some 16a commando sockets in a farm workshop. The workshop has a 3ph sub DB on the wall which is fed from the main DB on the other side of the wall, about 25m away. The sub DB is supplied from two lots of 6mm2 twin in 25mm...
  7. M

    CHARACTERIZING AN UNKNOWN SOLAR PANEL

    This a question from a Complete Newbie! Please bear with me! I have a 2.5W; 8.7V small solar panel, but of unknown I-V characteristics. It has been very difficult to trace manufacturer's sheet. THE particular quantities needed urgently are: (1) THE NUMBER OF CELLS; and THE REVERSE SATURATION...
  8. Brainwash

    Gas Fireplace switch not connected to Electrical Panel?

    Hi all I want to replace the switch that turns on/off the gas fireplace and cannot find a breaker that would shut off the power to the switch. I thinks it's a stand alone switch to the fireplace. Is this correct? Is it safe to disconnect and replace? Thx!
  9. D

    120/208 on single phase panel

    I’m replacing a timer based contact for a restaurants outdoor building lights, sign, and parking lot lights. The panel feeding the old timer contact equipment has a black phase, a red phase, a neutral and a ground. Each leg has 120 volts to neutral but has 208 volts between the two phases. Is...
  10. LewisM

    Part Number of a busbar kit for a Square D Panel

    Hello, does anybody know of a part number of this type of busbar kit thing for a Square D Speed D Panel Board? Couldn't find any part numbers on the unit itself. Some Pictures
  11. IKETBeD

    Can't setup generator in close proximity to service panel.

    How many feet can 10-gauge Romex run (inlet box to service panel) and still properly support 30-amp inverter generator? Do I also take into account the 25-ft of 30-amp wire (3-pronged locking) that connects the generator to the inlet box?
  12. O

    Bigger panel or upgrade service?

    Hey guys, I just purchased a home that was built in 1960. It has a 100 amp service coming Into the house with only 12 breakers in the panel. A buddy of mine who is familiar with electrical keeps hounding me to upgrade the service to 200 amps. I don’t think I really need 200 amps. I was...
  13. M

    Brew panel

    I built a panel for brewing and tried it out yesterday, it's is designed to power a 6kw element in a a 70 litre stainless kettle. It ran great doing a 66 degree mash controlled by the PID for 60 minutes, all other controls like pump control, amp and flow meters ran like a dream. When I stepped...
  14. T

    Alarm Control Panel

    Good evening all, I was just wondering if anyone could lend a word of advice/help. I am not very good at DIY unfortunately I am a first time buyer having moved in around 3 weeks ago and today virgin media come to install my internet, however I think he has drilled through the wall close to...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Back
Top