Hi all,
I've picked up a pair of these: Hue White and Colour Ambiance Nyro Outdoor pedestal | Philips Hue - https://www.philips-hue.com/en-gb/p/hue-white-and-colour-ambiance-nyro-outdoor-pedestal/1745530P7
Hue Nyro, Pedestal lights. The instructions state that they want to be mains wired into...
I read once, never seen one for sale, that there is a solid brass replacement for the standard 13A fuse in a 13A plug. This is to eliminate the fusing in the plug, which is handy when having a heavy appliance plugged in behind itself, like under worktops which are isolated and fused by an FCU...
Afternoon all! I’m wanting to buy a standard outdoor security light with a sensor for a garage wall… there’s a couple of sockets in the garage so I’m just wondering what would be needed to make the light able to be plugged in? From what I can gather; a 0.75mm flex cable about 3 meters long, 3 or...
Power connection of unknown source (prob socket spur) connected to outdoor light. Can i disconnect the existing light. Connect up RCD plug and then connect a switch to control a new outdoor light like pic
Hi all iv bought a Clarke xe18/200 3phase compressor it’s 4 hp and 50hz it was hard wired so didn’t come with a plug or flex what amp 5 pin plug do I need and what size flex attached is the details of the amp age , can you help
Many thanks
So I have an old pendent light. There was a 14/3 line and 2- 14/2 lines connected to a single light fixture. I re-wired it the same way back into a J-Box and then connected it to another 14/2 line ( so instead of it connecting to the pendant light it's connected to a new 14/2 line). That 14/2...
Hi all,
Washing machine plug and socket melted around Neutral pin. Whilst removing socket faceplate, noticed one brown wire was not in the terminal. May have come out of the terminal when pulling the socket forward or may have been out all the time.
Is this lose or disconnected live cable the...
I am building an outdoor kitchen and have run a subpanel to the kitchen. I have an arc-fault 20 amp breaker with 4 GFCI WR outlets wired in parallel around the kitchen. They are caulked appropriately, with weather rated covers, etc. but for some reason, every time I try to test the outlet - they...
So I unplugged my freezer to move it over a bit.. tried to plug it back in another socket and noticed it wouldn’t go all the way and sit flush, when I checked the plastic has split making the two bottom prongs sit at an angle. Help ASAP don’t want my freezer defrosting.
Hi. I have a kenmore 1988 dehumidifier that still works great, no problems what so ever except for the other day i noticed when its left on for an extended period of time the plug gets warm, not hot. I read warm is normal, but others say its not normal and that there could be a loose connection...
Hi everyone,
UK btw.
Not a sparky, but have some idea of electrics from fiddling with guitar pedals and a-level physics!
Just wanted a bit of advice - we have a dual socket in the kitchen, one plug of which does not work for the kettle (2000w draw according to the base), but does for the...
Hello,
I have a CEE to UK plug adaptor, when I plug something in I need to press the plug with force. I noticed inside the earth pin hole, it was very scratched and some plastic coming off from shutter part. If I use a Plug with a Plastic Pin plug, It is easier to plug it in.
Is there a way I...
Hi,
I am looking for some advice on the best way to install 5 double plug sockets into my garage, all of which will be running multiple computers.
My CU is located in the garage.
Would it be best to install the sockets onto their own ring main, or to add them onto the existing garage circuit...
I'm charging a PHEV from a standard plug socket, and it works. However I purchased an extension and the standard plug going into the socket has melted... it got a bit too warm for a bit too long.
Are there recommendations of specific plugs and cabling that could take 3kw comfortably for...
While visiting some friends down south I noticed they still had the cardboard wiring info on their coffee maker, so removed it as not for final use. What was curious is it specifies a 7A fuse, and while I have seen and used some odd ones before (e.g. 1A, 10A) this first time I have seen on...
As per title any ideas, car just cut out dead and will not start unless I pull the 2 wire plug off the high pressure pump solenoid. I also get no reading at all on the dianostic fuel pressure check. I have 72 psi when connecting my fuel pressure gauge to the line.
Called to look at a job today for a previous client. Tumble Drier giving off 'funny smell' and tripped the RCD - Called out her appliance insurance plan people, who suggested it was the fixed wiring - hence why she wanted me to have a look...
Plug and socket well and truly melted...
So I'm home servicing one of my Stihl machines (2 stroke brushcutter) and my local dealer apologised that technically it should take an R (resistive) type plug but they're hard to get at the moment and a non would work fine - what's the difference??
NGK BPM6A -v- BPM6(R)A
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc