I have an inverter powered by a car battery that I use when 220V power goes off (see block 1 below). I use a battery charger to charge up the battery before I can re-use it (see block 2 below). Id like to connect these devices so that the battery is charged when 220V power is available. (A...
Hey all, thanks for having me.
I'm fitting a GPS tracking system into my van (Renault Trafic 2005, 1.9l Dci) and I'm trying to install the imobilisation feature. Once wired in it will let me remotely disable the fuel pump.
However, I'm struggling to get any information on the wiring of the...
Hi all. I decided to sign up to reach out to some experienced folks who may be able to point me in the direction of how to make this work (and more importantly, the right way).
This is going to be a piece of cake for everyone here (but me) I am sure. To keep a long story short, I am setting up...
Can anyone please tell me how to wire 3 8Pin relays together? Those 3 relays are for access control controlling the doors, so when the fire alarm triggered will disenergized those 3 relays and unlock the doors. Thanks
Hi Guys
I'm wiring up an electric roller blind soon, putting on a conventional up/down/centre off retractive switch.
Would like to install a smart relay in parallel but cant seem to find anything out there ?
Ideally something like this (but this is purely on/off control only) with nice easy...
Hi, I am not a qualified electrician and am doing a little DIY project.
I want to automate the lights in my garage. I have lightwave RF in my house (sockets and switches) which are great but the switches only work on dimmer lights.
Iv brought a relay which I was hoping I could use instead of...
Hi - I have just wired a 7 pin towbar using supplied harness kit with by pass relay . (2012 Megane Coupe)
1 issue discovered is my LED indicators on trailer remain permanently lit with dull glow? ( Checked trailer lights with another vehicle & lights are OK )
Otherwise lights works ok including...
Hi all, i´m new on here and really hoping for some good advice. Not getting much response from an owners forum!!
My Seat Altea is fitted with a single horn. There is a number 53 relay fitted to the relay panel and I believe this is for the horn.
I want to fit twin horns in place of the single...
I'd like to add individual footwell lighting and have the lighting come on when each door is opened individually. I've found the wire locations and looking at the wiring diagram, I not certain which way to wire a relay to properly detect when the switch is open to trigger the LED light to come...
Hello and thanks for the interest. I have a little dilemma and was unable to get an answer anywhere.
I'm trying to fit a SPD and an over/under voltage protector to my existing "Main Switch" and "RCD" setup. my question: is the location of the SPD and surge protector correct? thanks
Ive just purchased on old electrical device tha i believe is battery operated but has a realy on it marker - RES Load 5A - 110VAC or 24VDCC - coil DC 6V.
my question is what should i connect it to to test it, battery or electrial transfomer?
Can anyone recommend a wireless relay to trigger an oil boiler. Currently there is a huge buffer tank which is heated by a log fired biomass. The boiler is being replaced with an oil boiler, but the buffer tank is staying, as the tank was installed during a renovation which means the tank would...
Hello there,
I'm in a situation whereby the customer wants a light switch either side of the bed, and one by the door to control the centre room pendant. Unfortunately the type of switches they have across the rest of the house doesn't produce an intermediate switch.
Does anyone know any off...
My 92' Firebird that I just acquired will not start. I bypassed VATS security
with resistors so the security light now shuts off. I replaced my positive
battery lead that was shot and the only thing that happens when I turn the
key is the temp gauge fluttering. The relay only has 0.5 constant...
kalgran
Thread
gauge
light
no power
power
power to
relay
security
starter
temperature
won't
Hello,
I'm trying to build a 12v circuit where a npn laser sensor activate a pump but I have no idea on how to build it. Its pretty simple but if I hook the laser to the circuit it looks like there's not enough current passing through to power the pump. So I think I would need a relay right...
Trying to replace an old relay in my well pump. When I search for the product id 38-T129C4238 it says it's been discontinued..
The only other things left on the label that are legible are:
18-811
256 V 60 HZ
A P - 277 VAC
Product's Unlimited
Can anyone point me in the direction of a...
Thought i would put this out there for any experience faced with this design issue.
TP Immersion heater 11KW, has built in contactor, coil voltage 400V
I want to bring in the immersion heater via control system and ideally not alter the immersion heater package.
The control system can operate a...
Hi guys, I want to switch a 24 v load on using just the continuity of NO voltage free loop. Does anyone know of a relay or device or method that I could use to do this?
thanks
Hello
I currently run a lead acid 102A auxilliary battery under the bonnet of my Nissan Patrol for the purpose of powering a 70 litre Waeco car fridge.
I intend putting in a second auxilliary battery (AGM type 130A) in the rear of my Patrol to get some more life out of the fridge.
The current...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc