Hello, new guy here and I'm not sure of correct section or even correct forum for this question. At a local thrift store I purchased a Warrick 1d1d0 relay, looked interesting for a dollar. I play with home electric power and it looked interesting. Any way the input is 115v and the output is...
Hi, I am new here. I am a farmer in the Highlands of Scotland working on an electrical fault in an old Massey Ferguson 390T tractor made in 1992. I think the fault may be in a relay. This is a 7 pin solid state relay labeled "warning light dimmer" on the circuit diagram (see below). The Lucas...
hey :) i have a fuel resistor relay that a bloody melomy has chewed, it also chewed a hole in my battery and made it leak. i have attatched photos, just wondering if anyone could help me out with which black wires go where to attach the plug back onto the relay? much appreciated if anyone can...
Hello guys
I own a BMW E39 which developed a crank no start issue. No codes are being thrown but my initial thought was fuel. So I checked the fuses (all ok) and then moved onto the relays. I removed the relay and its ok then checked the socket and discovered the relay base is showing 4v on the...
Is it possible to energize a contactor/relay from multiple toggle (not momentary) switches in a way similar to 3-way switches?
If so, what components and setup would do that?
The purpose is to control lighting from several sources and the reason for not using simple 3-way switches is that the...
Hi there, I am looking to charge an auxiliary windlass battery (130Ah lithium) that is located 35 feet away from my main bank (1030Ah lithium). My charging input will range from to 40 to 100 Amps, but I need to keep the wire size to a maximum of 6AWG. Do you know of any current limited charging...
Hi,
I’ve been trying to retrofit AC to my Mercedes sprinter motorhome, I have most of the kit but some of the wiring is missing.
I have managed to find a decent wiring diagram for the entire van but having trouble with this section.
I know the symbols (ringed in blue) are called...
Hi,
Apologies if this is the wrong place for this but want to confirm something.
I have wired up a 12v lightbar on my ATV using the attached wiring loom layout, but I have been told by some that this setup will cause the battery to drain/go flat over time due to the relay always having current...
Hi there.. I have a 2013 Relay. The electric window switches in the drivers door started playing up, only working intermittently. I took off the door panel and looked at all the wiring.. all looking intact as far as I can see. The passenger window works from the passenger door switch perfectly...
Hi,
I have an aftermarket ignition coil harness utilizing a 5 pin relay, the relay is corroded and doesn't work. It's also discontinued by Denso and they don't have a wiring diagram for it (P/N 056700-7240).
I managed to source a similar harness from a later model which has a slightly...
Hello all. I am having an issue with a 12V DC Relay I am trying to install to run a kill switch on a John Deere Diesel engine that runs a high pressure water pump. I have the relay wired in such that it will send power to the ignition when an electrical signal comes from a water sensor in the...
Hello,
pls do no kill me for being this stupid (i am a videographer in nature :), and i need to make an order before my electrician returns from hospital...
I want to add leisure batt to my 1987 VW t3 Caravelle along with volt sensing relay and i cant figure out how to calculate the system...
This unit is running two showers. Unit was smoking while one shower was running, never tripped the safety switch. Power to one shower is cut off while the other is in use. Is it ok just to change out the relay that had burned? I'm not an electrician but one will be doing the work. The house is...
Hi all
I would like to wire a GSM gate opener to my gate motor, but I'm not 100% sure about the inputs.
I would like to be able to call the GSM and have the gate open and remain open until I call the GSM again. My plan was to wire up the COM terminal of the GSM to terminal number '2' on the...
Hi, I have a 12V output from a control box that lights an LED. I want to use that output to switch power to a camera, but don’t want to lose the LED. The LED has a resistor in series.
My first thought was to just put the camera in parallel with the LED, but then thought a relay with the coil in...
Hi,
I purchased a relay and relay base in order to control my doorbell whilst using a Nest Hello: the Nest product takes 24V, whereas the doorbell only wants 8V. So the relay closes the circuit when receiving power from the Nest and the doorbell is separately powered by an 8V transformer.
All...
Hi folks, I did post months ago about my Isuzu pick ups interior lights not coming on when doors open but I never did any more about it in the summer. Now that the nights are closing in I must get it sorted.
I have a dome and a reading light, both work fine when switched to on but neither come...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc