Hi there.
this is my first time on the forum..
I'm currently doing a quote for electric heaters on appartments, they have just had hudge quote to replace their gas flues as there not to current regs and are in need of replacement. The gas flues are in ducts that rise through each flat. I'm...
Hi guys,
So basically I'm coming here looking for some friendly advice with the intention of eventually getting an electrician out to make sure I'm not messing anything up (I'm based near Swindon - recommendations welcome!). I just want to do as much of the prep as possible.
I've put together...
Morning All,
I have a customer request for a wireless PIR system, receiver above the front door & 3 sensors in the garden. The lights required to energise are all LED and total 45w.
Ive bench tested the timeguard offering (which does say not for use with LED) and sure enough it doesn't turn...
hi every body.
need to make connection of a schneider contactor LC1D40A with schneider RM17TG20 phase control relay.
need to how to wire between these two to make the relay will trip the contactor when single phasing happens in 3 phase system.
schematic diagram will difficult to understand...
Muhammad Abid
Thread
connection
contactor
control
diagram
phase
relay
schneider
supply
Hi All,
I wonder if you can help me....
I've been designing my own solar solution recently and built a small example that worked really well. I've taken it into production and working with an electrician friend of mine, here is what we setup:
I have a solar panel connected (through a DC...
sblezza
Thread
blowing
diy
electric
electrical
needed
relayrelays
setup
solar
Hi,
Is it possible to fit an extra immobilising relay* to amodern car loom with start-stop fuel saving?
(in addition to the manufacturers standard immobilisingsystem)
This is the logic that I’d like =
Initial turn of key = only start engine if fitted securitysystem is happy to start AND...
geraintv
Thread
additional
calibri
car
fit
relay
roman
saving
times
I need to switch 2 lights at the same time which are on different circuits. I can't gain access anywhere (hard wood floors and untouchable ceilings but I can get to both switch cables. The simplest solution would be a 1-gang, 1-way double-pole switch but I can't find one. I've looked at using a...
pebsham
Thread
can't
circuits
double
light
light switch
pole
relay
switch
Customer feeds an outhouse via a RCD fused spur. Tripped a couple of times in the last 6 months and because there is a freezer out there potential to not know supply has tripped and lose all thats in the freezer.
Anybody had cause to use some sort of alarm in the event of the RCD tripping...
XPSAC3721 | Preventa XPS AC Safety Relay, 230 V ac, 3NO Safety, NC Auxiliary | Schneider Electric
Hi all, the above attached E-STOP safety relay I use regularly use when carrying out panel build upgrades from 1960-70s panels which most of our machines have, anyway my question is. we have a...
I want to remove and bi pass the circuit completely, I know its possible to trick the bike into starting by simply bridging the wires at the switch but I need to drastically shorten the loom so this really isn't an option.
I have a diagram in pdf form which I will post later but for now I'm...
Hi guys and gals,
Where is best place to get a 230V relay urgently? Never had to get one before.. its to switch between two 8A heating elements, from a domestic mains supply. I think the current one is on a din rail but its under a bath so there not a problem with space or mounting.
Thanks in...
Today i found that there are two questions about IDMT relay which i dont know how to answer.
1. What will haggen if electrician forget to insert the "plug" in the IDMT protection relay?
2. Discrimination is important in electric circuit protection. Please tell me how to apply the plug settings...
Hi all
I am working on a job and I am having trouble getting my head around it. Normal systems are fine but this is causing me a headache.
It is an S plan with an additional pump so both the DHW and CH have a pump and a valve, I know that the pumps have to be split due to it back feeding but...
Having problem with a PIR. It's only supplying 1 x garden light @ 60w. Very small load. Basically sensor is switching over fine. However the light is illuminated constantly very dim. Once PIR kicks in it goes to full brightness. Though I had faulty sensor took it back and swopped it.... Same...
Hi,
I have and regularly install Castle Enforcer alarms by Pyronix.
i have a question and hoping someone may know.
how can I trigger an input from a third party device, so for example how can I close a relay on another device or put a 12v feed in to an input on my alarm?
i want to be able to...
Hi Guys,
I have a 'garage' style electronic hoist.
An example of the type is: Hilka Pro-Craft 500kg Electric Hoist | Workshop Equipment | Screwfix.com
As you can see there is a two position switch, and inside there are some capacitors for starting voltage. The Switch on one 'side' is Live...
Neil Scrivener
Thread
control
motor
relay
requirements
safety
switch
voltage
Does anyone know of any firms which manufacture G59 relays? We're struggling to get hold of anyone who can sort one before the deadline.
We've asked Andy@ Sibert but he won't be able to sort when till early Jan
I have a small utility room at the end of my garage, it have a fluorescent fitting for lighting controlled by an infra-red sensor. I decided to change it because the tubes and/or starters fall over at the most inconvenient namely winter time when it is dark.
I have changed the fitting to a...
Hey all, fairly new to this so bare with me,
i have an interview this week and Iam expecting a skills test does anyone have any idea what I could be facing? Or what you have experienced, the job is in a food processing factory.
ive heard rumours of having the wire a dol with pilz relay?
not...
Is there any way to find a DIN rail mount SPDT time relay with adjustable transition/changeover time. Need to automatically switch between two reversing contactors without mechanical interlock depending on the coast time of a relatively high inertia load.
It might be more cost-effective to use...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc