Do I need to have 2 power sources if I have a three way switch and a single pole switch in the same electrical box? The three way will have another switch at a different door for inside lights. The single pole will be for an outside light.
Had to do a CU change in this lovely heat, so naturally it was a bit of a bugger...
Replacing a Wylex skeleton board with Type 2 breakers for a Wylex skeleton board, as client wanted it to remain hidden.
The previous board "enclosure" was made up of the nasty brown plastic front (always...
It is a 6.5kW thermostatically controlled water heater if you ignore the rest of the gubbins.
So that would be a Purpose #6 for diversity ie: None allowed. = 28A.
But you could treat if like a cooker too. Purpose #3 ie: 10A + 30% FL current over the 10A. = 15.4A
What do you think?
Thanks
Hi guys,
Have an option of an old, but really solid superb condition and well made large +/- 200ltr compressor from Denmark. Rarely used since purchased/Build 1987.
Only supply I have is 230V Sing/Ph. Never had any dealings with 3 Ph.
First name plate.
Grundfos 3~MOT MG90LAR-24F115 No...
Hi... I am Shamsul from Malaysia
I have a question regarding to earth fault current if occur inside 240V single phase customer house/building
1.May explain how the earth fault current flow route
2.If got local earthing was connected from ground to 11kV 3phase DEAD line, is it the fault current...
Hi there
I preface this query with: I am an almost complete electrical novice. I need to control the speed, startup and slow down of a 2100W induction AC motor through a VFD. My workshop has ordinary Australian 240v single phase supply. I can find plenty of VFDs that convert single phase to 3...
Buoyed on by my first successful ceiling rose replacement, I’m now doing a second one, but have come across a slightly different scenario.
In this ceiling rose there are more wires than previously, so my question is, is it ok to place multiple wires into a single connector in the new light...
Hi there,
I have currently started working on a farm and they are having a new 100a 3 phase supply installed.
This is being terminated in an external enclosure. They then want to carry this 3 phase 150 meters to a barn and at this point split it into 3 single phase supplies. Is this even...
Hi all, just about to do the paperwork for a new RFC at an HMO. Its a while since I've done any paperwork as I've been doing a lot of subbying for the last 12 months. I use electraform and have just seen these single circuit certificates (SCC). Do any of you guys use these, or do you just fill...
(UK). I am renovating a 1988 HD 1200 XLH Sportster. The previous owners have butchered the wiring so I am rewiring it by hand.
There are a few places in the wiring where a single cable needs to connect to two others. An example is from the fusebox. The output for the Accessories 15a fuse needs...
hi
i'm putting in some exterior lights for the shed.
ive drilled a hole through the wall, put conduit through the hole to protect the cables and put a junction box over the holes. inside the house is mini trunking and single core cables. outside is swa.
can i just take the singles...
If I have a 240/480 volt dual voltage single phase motor connected by 2.5mm 2c+e to an isolator and then just 1mm flex coming out with active, neutral and earth connected is it possible the power supply to be 480v or is it most definitely 240v
Good morning all. I am new to the forum and hoping someone can help with a query i have. Currently i have a double light switch which operates two separate lights at each end of my kitchen. I would like to change the light switch to a single allowing me to turn on/off both lights at the same...
Hello everyone
I have just bought a new lathe, (used) its on its way to me from other end of the country now.
I have only just realised i may have an issue.
The machine is 3 phase and i was intending to go down the VFD route but because its a dual speed motor im not sure i can.
See attached...
I am trying to fix a single phase ac motor but need some help. When powered on and put off load, motor humms but doesnt rotate, its sort of magnetically locked because even trying to rotate by hand it very hard to turn (motor was removed from housing and therefore I have stator and rotor...
I've got a cooker hood extractor, it only has a live and neutral cable, I've only got a single socket to install it. Can I put a 13A plug on the end of it?
I’m replacing a timer based contact for a restaurants outdoor building lights, sign, and parking lot lights. The panel feeding the old timer contact equipment has a black phase, a red phase, a neutral and a ground. Each leg has 120 volts to neutral but has 208 volts between the two phases. Is...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc