Hi all,
Half way through an installation as a subby on someone else’s electrical contract.
It’s for a church, in which they’ve asked me to run 2 radial circuits.
Circuits 1 and 2 split a total of 10 fused spurs, 5 on each radial, each with a 3a fuse and on a 20a mcb.
Cables are run under...
Hi Guys
Need the experts advice again please .
Recently added a new double socket in a kitchen off of the existing ring final.
At last minutes notice I was asked to see if I can add an outside light by the back door. (Which is right next to the new socket that's just ben added)
The question...
Hi
Just getting started with a view to DIY electrics on my house extension in a few months time, and ideally would like to map out the current circuits so I can plan the best way to join up, or where new circuits may be required etc.
2 Questions
I reckon I can do some DIY non-live testing of...
I bought a number of 20AX grid switches with printed labels on them e.g. washing machine. These were to put an isolator above the work top for a 13A switched socket under the work top in the utility room. Electrician says no as the spur will be off a 32A ring the switch must be capable of the...
Hi folks.
I cut one of the cables on my ring circuit, attached the 2 now separate ends to a new 30a junction box, and then run 2 additional spurs from the same junction box, using 32a twin and earth, on the end of each of these new spurs is a twin plug socket with usb.
I did the work with my...
Hi,
I'm doing some work on a room I want to convert into an office space.
It currently has three sockets in it. One has two neutral and two live wires connected to the socket, the other two have 3 live an neutral wires (this wiring is done circa mid 60's we think.
I plan to add about 2000kw...
Ok without any football team references... Mace are the managing contactor and spurs have nominated contactors. So mace wont be liable to any delay clauses due to this. I read in construction manager journal approx 500 sparks ( including supervision ) but not sure. Anyway my point is with that...
I am refurbishing a house i bought last year & looking for thoughts on whether the following existing wiring is right/ safe. I dont think it is but would like to check as it looks like spurs of a spur to me. The CU was just replaced by local electrical contractor & all circuits are he says...
Hi, this is my first time on this forum so I hope I'm in the correct section.
I've come across a strange socket wiring set up in my own home. I was baffled at first as to how at the consumer unit I had a ring main set up (2x 2.5 T&E fused at 32A) but radial setup at each socket (1 cable).
What...
I have a socket which is connected off the main circuit ring.
Just wanted to know if it's possible to add another socket spurring off this second socket?
(Please see attached image.)
If it's against regulations, then
1) what's the worst that could happen? (Will my circuits blow up?)
2)...
father In law grabs me and says
"now we've had our extension finished can you help with some outdoor sockets?, they have put an outdoor socket on the side, can you connect the sockets that feed the hot tub back up into it"
So on first glance there is an al weather IP rated twin socket on the...
Afternoon to all!
I have to replace my current shower pump as it's on the way out, it's loud at the best of times so I have taken the opportunity to replace with a quieter unit but my problem is it's a different make and as a result the power supply is also different, the new pump comes with a...
Hi
I recently purchased a house (built and wired in the 80s).
I removed one of the sockets to do some wallpapering and I noticed that it has 4 hot+neutral (+earth) wires connected to the double socket (and I'm assuming it's all solid core 2.5mm wiring??).
I'm not sure if it's connected in a...
Hi,
I have recently completed an intensive electricians course and I am at the stage where I am trying to get practical experience wherever I can.
One of my jobs, which I am planning to use to join a competent person scheme, is to change my consumer unit and wire up my extension.
At present...
what is maximum amount of spur sockets taken from a main , the main amperage can be changed easily the wiring is 2.5 and a ring main is not possible without a lot of work as this is a large old house which has been wired this way , there will only be one large consumer a water heater .
Hi guys,
I understand that when you spur off a circuit if you have a 1 socket then you do not need to have it fused but if you have 2 or more it needs to be fused.
What is the principle behind this?
Thanks
Problem with neutral.
The other day we had a problem with a circuit not working correctly.
The circuit is a radial,wired in 4mm singles,in metal trunking powering 4 switched fused Spurs.
The circuit had previously been dead tested,with no apparent problems.
However when the circuit was...
Hi I have a situation where there are Spurs under sink zone 2.
would it be ok if fittings where ip rated or fittings were enclosed in ip rated housing.
the circuit is protected by an rcd .
Lim pretty new to testing by would appreciate any advice.
Ive tried to find solution but was not able to...
So you can spur off Spurs on a radial socket circuit, is this because the cable is protected via a 20amp breaker at the board compared to 32amp on a ring?
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc