table | Page 2

table

Recent contents View information Top users
  1. H

    Wiring a table lamp direct to a mains light switch?

    Hi all, was wondering if is possible to wire a 3 amp table lamb directly to a mains light switch? The light switch is used for an outside light has two brown wires going to the switch and two blue wires in a chocy block going nowhere? Thanks. Steve.
  2. Andy5678

    Table saw switch

    Looking to replace a table saw switch. The saw has a slow start motor, so the usual retrofit start stop switches won’t work. Anyone ever replaced one/recommend a retrofit switch?
  3. J

    The First Table in Section 7 of Onsite Guide....

    The first table in the OSG, p64 (it has no table name). It says the following maximum loads are assumed per circuit, and then it lists circuits and their rating, along with Load. My question, is this table showing maximum load that it's recommended these circuits should reach? Or is the Load...
  4. King Mustard

    Can I use a dimmable LED bulb in this table lamp?

    We have just bought this dimmable (three-stage) lamp. The descriptions states: "Bulbs required 1 x golfball SES small edison eco halogen bulb" Do you think it has to be an E14 dimmable "eco halogen" bulb? Or do you think I can I get an E14 dimmable LED bulb?
  5. N

    Toggle Flick Switch 12V on Table Lamp?

    Hi All, First time poster here. I'm an ex-plumber and lamp making diyer. My question is this: Is it safe to wire a lamp like the one here (image 1 below): with a toggle switch as seen here (image 2 below): Switch type: toggle Contacts configuration: DPST Switching method: ON-OFF AC...
  6. LeeH

    Asked to bond a sink (table)

    I have been asked to ‘bond’ some tables or industrial sized wash bins by the engineering supervisor here at work. People stand and work out of these. Simple structure with water that’s filled from a hose. Q “can you bond these tables, and what do you think?” Me. “Well, seeing they are not...
  7. S

    2365 coursework 615 help with table 1

    Hi all, im studying 2365 level 3 and working on the coursework, im down to question 4 working on table 1, now its asking for cable lengths, with no dimensions on the images how am i supposed to have any idea how long the cable will need to be? theres no structure information so i dont know then...
  8. A

    How to rewire a table saw

    Hi guys The power cable on my table saw attached to the motor came off when I changed blade to 45 degrees. Turned saw upside down and the power cable was hanging loose, the only wire coming out the motor is a red live cable, how can I reattach the power cable when it has live and neutral wires...
  9. S

    Extending table lamp flex

    I have a table lamp fitted with 2 core 0.75mm flex. I wish to extend the length of the cable but only have 2 core 1.5mm flex to hand. Can I use this, or must the flex be the same diameter both sides of the join. Sorry if this is a ridiculous question. Thank you for your advice.
  10. Zdb

    Table 41.3 18th edition

    Anyone got the updated maximum Zs values that they'd like to share?
  11. R

    Finding the correct cable table

    A lot of these mock exam questions are not specific about armoured or non armoured multicore cables, flat twin or not etc, the correct table to use can be a bit of trial and error until you get the correct answer for Volt drop for example.
  12. W

    6 3kw table top ovens and hobs

    Hi guys some help required!! My sister runs a centre and has bought 5 x 3kw table top combined oven and hobs they are supplied with plugs which cant be removed as that will invalidate the warrentys. There are 3 spare slots on the consumer unit how can she safely run all 5 appliances. she says...
  13. G

    Table 4.1.2a/b in Electricians Guide

    Could somebody please clarify the difference between tables 4.1.2a & b. It appears to me that the difference is in types of circuit breakers - B or C depending upon max test loop impedance. Is this correct and which measurement do they mean by test loop impedance?
  14. O

    Dual CS 430 Turn Table issue

    We have a massive selection of LP's - not all on CD or downloads! Some of which I'd like to listen to We also have an early 1990's Dual CS 430 turntable - but the central spindle will not rotate free - there is no obvious way to clean or lubricate it and despite doing a number of internet...
  15. John Lundrigan

    Advice on TABLE 41.3 please?

    Table 41.3 provides max Zs values based on Uo = 230V. Can this this table be used to assess Zs for Uo = 110 v ac on a reduced voltage system. Perhaps reducing Zs pro rata? Thanks
  16. Edtwozeronine

    Can anyone point me towards a complete installation method table

    I have one in the OSG and I have the BSI IET (size of a yellow pages) regs book. I found this too: http://www.tisoft.com/en/support/help/electrical/reference/bs7671/tables/table-4a2-schedule-of-installation-methods-of-cables I've chosen A for air tight conduits in the concrete wall of a...
  17. D

    12 volt metal table lamp for sale.

    Hi all. I am planning a metal table lamp. The light will be a 12 volt LED fed from a plug in transformer, so there will not be any 240 volt cable or connection to the table lamp. Do I need to earth the metal of the table lamp?
  18. Wilko

    How to modernise an old brass table lamp ?

    Hi All, the story so far : Customer has asked me to make her old brass table lamp work. How hard could it be? No earth, so first step was some new 3 core flex and a brass lamp holder that's got an earth point. An inline switch and I'm away. But no, the new flex won't fit up the stem of the lamp...
  19. CDB

    Diversity Table A2 OSG P118

    Morning all, Thumbing through the OSG guide today and I have a couple of questions regarding the above table. Firstly, just a idiot check but electric showers would fall into no.5 water heaters of the instantaneous type. I know this but so often doubt myself. Secondly, No. 9. Am I right...
  20. CDB

    Elec.. Guide.. Build.. Regs Table 4.1.2a - Is this a cooker mistake?

    Hi, I hope my abbreviated title caught someone's attention and makes some sort of sense. On page 58 of the Electricians Guide to the Building Regulations there are some standard circuits listed. In particular I'm looking at the cooker entry on page 59 and have a couple of questions: 1) Why...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top