table

  1. M

    MCS Registration Bodies Recommendation

    We are a long established NICEIC electrical contractor, any one please give their opinion and or experience on the companies offering MCS Registration and Assessment. There are number we have contacted including NICEIC, NAPIT and Benchmark. Any advice or other providers ? Thanks in advance.
    • Mattajack
    • Thread
    • certification electricians' talk green mcs napit niceic recommendation registration table
    • Replies: 18
    • Forum: Solar PV Forum | Solar Panels Forum
  2. R

    CPN 63A 30mA RCD

    Evening guysAs title says, Where can I get one from?What wholesalers sell them or what is compatible with them?Cheers
  3. S

    Installation Reference Method

    Hi What is the installation reference method for flat T&E cable, with capping and buried in plaster, am I correct in thinking it is method C as all the others in table F6 (page 150) in the OSG refer to insulation? Steve
  4. C

    Conduit Capacity

    can anyone help me im sitting my 2330 level 3 in a few weeks and been going over some past papers and found a question on conduit capacity, which if i use all the factors etc, the length was 12 meters, the table in the onsite guide only goes up to 10 meters, what would i then need to do?
  5. P

    SCC of BS1361 fuses

    Hi all, I came across a Hager consumer unit today that uses the small stubby cartridge fuses marked 1361. I don't know if they should have the short circuit capacity printed on them, but if so it was no longer visible. I did look in the BGB but couldn't find a table with the SCC listed, so could...
    • PB1
    • Thread
    • bs1361 electricians' talk fuse fuses table
    • Replies: 3
    • Forum: UK Electrical Forum
  6. kingeri

    OSG Table 7.1(i)

    Table 7.1(i) lists standard circuits that can be installed without calculation. The radial circuits are all listed as having a terminal load. Can they equally be used for socket circuits? Just to settle an argument!
  7. C

    Cable factors in trunking, conductors over 25mm^2.

    Hi All, I have been searching the forum but can't find this anywhere. Can you please see if my interpretation of this is correct: 50x50 trunking, 2m run with 1 90o bend. 4 x 50mm conductors, 1 x 35mm conductor. As there are no factors for over 25mm2 I have to work it out manually 50x50 =...
  8. Top Cat

    Little table for CPC sizes in 2 & 3 conductor cables

    Do not know if this has been done before but i find it useful as am always forgetting. 1.0mm cable has 1.0mm CPC 1.5mm cable has 1.0mm CPC 2.5mm cable has 1.5mm CPC 4.0mm cable has 1.5mm CPC 6.0mm cable has 2.5mm CPC 10.0mm cable has 4.0mm CPC 16.0mm cable has 6.0mm CPC
  9. S

    Metal Table

    Hi All In a small factory I do work in operators are complaining of getting static shocks from a stainless table. I have put it down to persons building up a charge and it discharging when they touch the table. It gets me thinking that does a small stainless steel table require bonding? Thanks
    • SKY
    • Thread
    • electricians' talk metal table
    • Replies: 15
    • Forum: UK Electrical Forum
  10. S

    Date of original installation

    Can anyone help with estimating a dates of original installations. It needs recording on the certificates but can't come up with a date. What are the signs to look for to estimate a date. Other than rubber cables and old wooden backed wylex boards.
    • sparkymatt1987
    • Thread
    • cables earth electricians' talk installation later original table
    • Replies: 5
    • Forum: UK Electrical Forum
  11. S

    Eaton rcbo

    Lads Im after a Two 16amp EATON EMBH 116R30 RCBO's, Does anyone no if any other type of RCBO will fit?. Im having abit of trouble getting them (been let down by wholesaler at last min). CEF want £110 for the pair!!. Need them for Tuesady.
  12. J

    Shower 10.8kw advice please

    Hello All Ive got to fit a new shower in a commicial building our company look after. I think the shower is supplied from a type c 50A MCB MEM mem sheild board. What i was thinking was replacing this with a type c 50Amp 30mA RCBO. Also would the max Zs for this RCBO still be 0.46 ohm as in...
    • James Sutton
    • Thread
    • advice aus electricians' talk james please shower table
    • Replies: 5
    • Forum: Australia
  13. W

    Frequency of Periodic Testing

    Hi Does anywhere know why I can find a table (pref. PDF) showing the frequency of testing for particular installation types? Thanks in advance!
    • Wiki-Electrical
    • Thread
    • aus electricians' talk frequency inspection installation periodic table testing
    • Replies: 5
    • Forum: Australia
  14. M

    BS EN 60204-1 Help required re : Earth loop testing of machinery

    Hi Guys, The 17th edition gives you a table of circuit breakers and their maximum allowed Zs, however as the 17th edition does not cover "machinery", we have just started working with BS EN 60204-1 "Safety of machinery - Electrical equipment of machines - Part 1 General requirements", and this...
  15. F

    Earthing table lamps

    Hi, I've just started making wooden table lamps, made entirely from wood with a GP 091 B 22 Brass pushbar (switch) lampholder attached to the top. The lamp holder is attached to the lamp via a small brass plate that it screws directly onto, the plate is attached to the wooden lamp via three...
  16. S

    Bonding of commercial catering equipment

    Just wondering what your thoughts are on this, have seen it done in a variety of ways, and the lads at work all have different ways of doing it, e.g. daisy chain from main bond to the gas pipe around each piece of equipment, another way to put earth straps at various points along the gas...
    • Sparky_Ben
    • Thread
    • around aus bonding catering commercial electricians' talk equipment table tables
    • Replies: 5
    • Forum: Australia
  17. L

    Conduit factors

    Good afternoon Gentlemen.I'm in the process of rewiring my garage so that I can join one of those fantastic schemes for my Part P.Question is this. looking at the OSG about conduit factors (Table 5D), it says about bends. Is this just bends in the actual conduit or does this include such things...
    • Litttle Shonet
    • Thread
    • aus bends conduit electricians' talk factors never table through
    • Replies: 3
    • Forum: Australia
  18. B

    Frequency of testing

    Hi Guys Having a senior moment, I can't find the tabulated guidlines for the frequency of testing. I know it exists somewhere....! Thanks in advance Billy ps Anyone know if I need to submit a diagram of locations of smoke alarms with the paperwork for a HMO going to the Council?
  19. S

    Online Sap Comparison Table - 43.3p vs 21p and others

    I did post a link this evening to a web site that was given to me and it shows the difference of the proposed changes. It is very detailed and I understand that this was developed for NAPIT members. Since posting it here it has not appeared, so I assume its not allowed. If anyone wants the...
  20. C

    T+E in 25mm steel conduit?

    Hi every one, Im new to this forum. FNG!. A simple question that I cant seem to find the answer to is can I run TnE in steel conduit? I know singles would be the best option but the customer has lots of TnE and wants to keep the cost down. I would strip out the cable but I dont have enough...
    • cuttys
    • Thread
    • 25mm conduit electricians' talk method steel steel conduit table
    • Replies: 11
    • Forum: The Welcome Forum

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Advert

TrueNAS JBOD Storage Server

Back
Top