Hi all I have a few questions about that video.
1. I don't understand why there are two isolators on the tails between the meter and the CU. One is fused and one isn't, so what's the point in the one that isn't?
2. Why would this 'require RCD protection' like the guy in the video says? I...
As seen in the pictures, I need the pigtail style connected to the other style. It needs to be fully weather proofed and safe as this is wiring for a light bar on my Jeep Wrangler. So please let me know how to safely do so, rather than just shoving the two together! Thanks in advance
This is a disconnected switch in my in laws storage shed. Sorry about the paintwork, it got sprayed when the walls were done.
I never realised it’s just an old toggle switch inside, mounted at an angle.
Hi, i was given measurements from the tenant and they happemed to be slighty wrong. Now iv already ran cables and the plasterer has already done his job. Looking at the pictures the tenant sent me, the accessorries seem a little close to the hob. What can be done now? Do you think its ok as it...
1. I have a vertical installation of a 10 ft 3" PVC conduit Schedule 40, weather head, 45 degree elbows. Do I have to glued these commodities?
2. I plan to install 400 ft of underground 2" PVC conduit at 36" deep on a farm. there are no buildings or structures on top. there is just...
Can’t seem to get the connections in ? They just keep coming loose, can’t seem to push them in either far enough ? Any ideas ?
https://pasteboard.co/JwSCDiT.jpg
https://pasteboard.co/JwSD4nmx.jpg
Afternoon all,
How do i solve these two questions, Feel like am missing something simple. doing my head in lol.
I need to learn the calculation for them both, I am struggling to work it out.
1.
Insulation resistance has been tested on five new lighting circuits in an existing large...
Just been discussing this story on the sun,
London flat to rent for £1,000 a month has a shower in the KITCHEN - https://www.thesun.co.uk/money/12796622/london-flat-rent-shower-kitchen/
I reckon there is no current EICR for this place, if there is then its not worth the paper its printed on...
What’s your thoughts on this,codes etc.
Quite a lot if these,on wall lights & chain hanging lanterns.
It needs some enclosure sure, but it was ok 20 years ago,& no probs.
I don't expect there's anything of interest here @Lucien Nunes but on the off chance if there's anything you want for your museum then let me know. I'll pay all shipping costs.
Hi All
Am continuously getting failed EICR'S sent over to quote on remedials for non fire rated downlights. These are lights in question. I see they have exposed conductors so would personally probably code 2 but what would code be for fire rating they are low voltage if that even makes a...
I ask you lege's if anyone has a clue how to remove these wires from this cable-plug-housing.
It is from (one of) the oval lights on the side of a Merc Sprinter 2019.
I managed to remove it from the oval light by first pulling up the grey tab, and then using the tab - levering it inwards...
Hi Guys,
I am looking for a bit of advice.
I am a landlord of a 1st floor flat in a small purpose-built block built in the mid eighties I think.
I have just had an EICR and have been cited C2s on the following :--
5.11 Provision of additional protection by 30mA RCD (See Note), c) For...
Morning,
I’ve got a cheek making this this my first post but...
Can anyone put a rough date these storage heaters? Specifically, do they look post-1974?
They’ve been disconnected but I’m
worried I’ll get face full of asbestos when I take them off the wall. They’re a Heatovent RAJ30 & a Creda...
I’m looking to swap out these switches and I’m not sure what I need. They turn on/off a bathroom light, fan and heater in the ceiling. I’m a beginner so please explain. See pics. Thank you!
Hi all
Not come across this MG board before (believe Schneider now own these and some of there stuff may be compatible) I am looking to change some of these MCB's over to RCBO's can anybody advice on which ones may be compatible seems theres limited information online. Thanks
Thanks in advance to anyone who can help.
These parts are modifications for a portable turntable, and I'm looking to save some money by gathering the parts myself.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc