underfloor heating | Page 6

underfloor heating

Recent contents View information Top users
  1. J

    underfloor heating on economy 7

    Hello all, Went to look at a job this week at a 1960s property. When the house was originally built electric heating elements were installed within the screed and have been operating happily on economy 7 ever since and client is happy with it. Just wondering if anyone knows of this still being...
  2. I

    Electric Under floor Heating Installation

    Hi, A first timer to the forum seeking some help. I planned to put an underfloor heating mat (total load 6amp) in one of the room at ground floor. Room is just couple of meters away from the place where Main Meter is located under the stairs. Work-wise, It doesn't seem difficult or complicated...
  3. Soulsurfer

    eStat 761 Underfloor Heating controller fault

    Hey all, Looked at an elements eStat 761 controller today as during loads of other jobs, customer said not been working for some time since buying the house. Checked RCD fcu and fuse, all good removed controller / stat and had 244V and yet nothing on the display at all, removed floor sensor...
  4. G

    Underfloor heating Controller

    The underfloor heating controller says it will be able to pull a maximum of 16 Amps. The supply is from a 20 RCBO. 2.5mm Twin and earth to a 13 Amp switched fused spur. The load side of the spur feeds the underfloor heating controller. The owner is saying that if for what ever reason the...
  5. S

    Contactor and Underfloor Heating

    I have a flat that has Up and Under Heating system. The ceiling heating is fine. The underfloor heating has not worked for 18 months plus. There is an outside Pactrol sensor, which feeds into a Pactrol Weather Watcher control unit, which feeds into a Benedikt & Jager K2-23A10 Contactor. I...
  6. O

    First house, want to retrofit Underfloor Heating. Many Questions

    Hi there, So first things first, just bought myself my first house . 1920's build in Wiltshire. Should have the keys to it next week, can't wait. Floor plan First problem is, no gas mains in the village. This means it currently has an immersion heater to supply hot water , storage...
  7. G

    mixer value on underfloor heating?

    HI all, installed a s plan, well i say s plan, heating up stairs and underfloor down, there is a 3 way manifold for the underfloor heating, a couple of question regarding that pls 1 actuator came , but there is a value i open with that stat so i assume i dont need the actuator ?? also i...
  8. A

    help to wire combi boiler for underfloor heating and house radiators

    Hi there. Major cyber pint for anyone that can help me with this problem. I have a vokera vision c combi boiler( which has volt free connections) that has to do the house radiators and one room for underfloor heating. There is one motorised two port valve for Radiators and one for the...
  9. F

    Advice re underfloor heating systems appreciated.

    Hello everyone, I'm about to start a self build of a 3 bedroom dormer bungalow on Anglesey. The house will be heated entirely by electricity and a couple of woodburners, using PV panels to generate some electricity as well. I am looking at underfloor heating and would appreciate any views on...
  10. D

    's plan underfloor heating relay tripping rcd

    Hello All I'm currently wiring up an underfloor heating manifold to an s plan system. the heating boiler takes its power off a ring main in a new loft. All circuits in the split consumer unit are RCD protected. I'm following the wiring diagram given in honey well wiring booklet ed 16. Page 14...
  11. D

    Adding underfloor heating to a s-plan system

    I am doing the electrics for an extension, part of which is to add a wet underfloor heating system. The current heating is s-plan, the boiler has a pump overrun. The plumber has put in a 2port valve and pump which feeds one zone on the UFH with a remote programmable theromstat. The...
  12. B

    contactor for underfloor heating

    Hi I've installed the electrics for an underfloor heating system. The system has 6 manifolds each with a small pump. There is then a primary pump that pushes hot water through the system from an aerobic digester next door. I have fitted 6 contactor each using a switch wire from the thermostat...
  13. P

    UNDERFLOOR HEATING Quick Question.

    Hi chaps. I've come over from the Tilers Forum for some precious advice. In an hours time I hope to install Electric UNDERFLOOR heating in my own bathroom, and I need some quick advice. Its about the temp sensor. I suddenly saw that it "should" be installed in a conduit to allow its removal if...
  14. S

    Electric underfloor heating fixing methods

    Hi all, not posted for a while so her goes... tomorrow im installing 30m sq of loose electric underfloor heating cable. im not new to installing the stuff but do much prefer the matt style system. With it been such a big area I want to make sure it doesn't start lifting when it's sat for a...
  15. J

    Bathroom underfloor heating

    Hi, I will shortly be installing underfloorheating to a small bathroom floor. There is currently an electric shower but this will be changing to a mixer shower running off a combi boiler. My question is, can I now use the redundant shower cable to wire directly to the underfloor heating...
  16. L

    Electric Underfloor Heating

    Hi, Which supplier would you recommend to go in bathroom under tiles? Thanks.
  17. C

    Underfloor heating, boiler , aga and cylinder

    Just wondering if anyone has every worked on a system with all of these working together and if so what cables I will have to run ?? ( look at title )
  18. D

    Underfloor heating L-E problem

    Hi, ok I half dont want to ask this question as it doesnt sit right but Id like your opinions. Installed a heating matt and after the tiles went down I did my final IR tests and there is now a problem between L-E at a reading of ~22ohms. The reading between L-N is still normal at 43ohms, correct...
  19. Prime Design

    Underfloor heating

    Evening all, I have been asked to install some underfloor heating as part of a full rewire. If I remember correctly the bathroom is no bigger than 16m square. I have run a 2.5mm cable to a location just outside the bathroom, the UFH will be on its own circuit protected by either a 16A or 20A...
  20. M

    Mid position valve and underfloor heating

    Hi all, just installed a polypipe under floor heating system to an existing Y plan, the valve is a V4073A,with this system the UFH stat should independently operate the UFHeating from the existing central heating, the snag is with the time clock off and the UFHeating stat on both the UFH & the...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top