This has happened twice, during a board change all circuits connected, first switch on, I have a idiosyncratic procedure for this, all off then mainswitch on,first RCD on,push test button then back on test RCD, breakers on repeat for second RCD, twice now I have had nothing on rcd button or...
Im in the process of quoting for a kitchen refit which ikea fitters will be fitting whilst i complete electrical works. Dishwasher, washing machine and tumble dryer are all freestanding but below worktop so my plan was to provide a switched fused spur with single socket for each. Now, ikea...
i started a new apprenticeship a few weeks ago (5357)
As it happens 9 of us (30-35 where enrolled) have level 2. So what they've done is put us 9 into a separate group and we don't have to complete 4 of the units within the course. At first I thought they meant the units at the level 2...
I'm wondering if any of you guys have installed any of the Chint range of consumer units that Screwfix have recently began selling. If so, how was your experience? Any good, or best avoided?
Hi, more advice required, about LED lighting. I'm so well out of date with these things. An Ashley/Rock HAL 96T batten holder was all that was needed in my time!
If you were posh, a fluorescent strip light!.
I intend to install LED lighting above the worktops. I looked at a video clip yesterday...
I have been told that in order to issue a Boletin the Consumer Unit and the Meeter cupboard both need to meet certain requirements. Can anybody say what these are please.
Does anyone have any experience with these ? Have been offered some at a great price but I have no experience of the brand whatsoever. I will probably try one or two out but just wondered if anyone could offer direct experience of these ?
Hi Everyone
I am aware that we now have to install metal consumer units in domestic premises now but at what point should we swap a plastic board over to a metal one?
The reason I ask is I've been to plenty of jobs where there is a plastic CU with no RCD protection. Ideally I would swap the...
I am about to rewire a large, 9 bedroom domestic refurb that has gained multiple 2-floor extensions and new loft conversion.
Original footprint was 135m2 ground floor, 96m2 second floor, new footprint is 180m2 GF, 127m2 FF, 76m2 SF. Concrete ground floor
Meter cupboard and original consumer...
Having a few thoughts on what should and shouldn't come under PAT testing under the COP 4th Edition.
I have no doubt wall heaters screwed to the wall and connected via a flex and FCU should be PAT tested, along with hand dryers, but does the same apply to Handwash units and 5-10litre water...
We are buying a newbuild property and due to the regulations, we are told the consumer unit needs to go in the dining room (as boxes are on the external wall in that location).
As the room will be painted dark grey we want to hide the box inside a cabinet by removing the back from the cabinet...
I would value your opinions on this.
I did an EICR and found two lights in a bedroom that are florescent lights so class 1 but the lighting circuit is old and does not have an earth. However, the lights are in vanity units, so you cannot touch the units without dismantling the vanity units. As...
Can't seem to find the answer to this online, on the OSG table 8.1 it divulges that only switches and sockets allowed of SELV Under Zone 2 which much have a minimum degree of IPX4 protection and shaver supply units complying with BS EN 61558-2-5 if fixed where direct spray is unlikely.
Does...
as title, I have a lot of car chargers to test. They are plugged into a socket via standard 13a plug, then goes into the charging unit, from there a lead to the car with the socket to be put into the car. They are for nissans and Mitsubishi cars. I have tried testing on seaward 250 but fails...
Hello
Kitchen Electricals
On the off chance someone is available at relatively short notice, there is a kitchen job to work on. The house and the job is modest and is all about getting ahead of the kitchen fitters as it has dawned on the householder that electrics are not included in the...
Hi all,
It says that if you install a new circuit you produce an EIC. Is that for the whole installation as well? or just that circuit. As the rest of the install may not pass current regs.
Many thanks
LH
Hi Guys
Client wants 3 wall mounted under-the-unit sockets for washing m/c, dishwasher and tumble drier. There is a lightly used ring cct available above the units. He doesn't want 3 isolation switches above the units due to having a stainless steel splash back and there's no access below.
Is...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc