wire | Page 2

wire

Recent contents View information Top users
  1. M

    Armoured wire for 24V system

    Hi All, I hope you are doing ok. I have a question regarding the 24V system. I am going to build a pergola and I could install 4 panels on it. The inverter and batteries would be in a building that is about 3-4m away. What armoured wire should I put in the ground in advance to connect these 4...
  2. F

    How to wire Hager CDA263U RCD?

    Can I connect the supply line and neutral to the terminals 2&4 and the load side line and neutral out of terminals 1&2
  3. L

    Burned wires on resistance faston connection on professional Coffe machine

    Hi all I have a professional coffe machine working at 220 V and it currently drain about 2,5 kW of power. I have made this simple and horrible schematic here just to explain how it works: Some time ago I changed the fastons on the resistance from brass faston to stainless steel faston and some...
  4. D

    Replace wire or breaker on septic pump?

    After 24 years my septic lift station pump and high water alarm needs to be replaced. It was tripping the breaker and the alarm was no longer working. When I pulled the wires out of the alarm, which serves as a junction box for the pump, pump float switch, and alarm float switch everything was...
  5. T

    Induced voltage on neutral wire

    Hi everyone, When checking my consumer unit voltages with the full board off, I stumbled across something head scratching. Measuring the feed from the DNO, L-N I read 242.3 V. Measuring L-E I measured 242.3 V and N-E I measured a steady 30 mV. When measuring the live side of the main of the...
  6. matt_d

    Smaller automatic wire strippers

    Has anyone come across automatic strippers to pull of the sheath of a cable already in a back box. The regular ones can do it to a degree but due to the design they can't get all the way to the end of the cable. Any suggestions for strippers to do this that have a smaller head and can pull from...
  7. J

    Metal building with living quarters rough in

    Metal building with living quarters the panel is on the outside and about 20 feet away from new build that will be 2x6 what type of shielded wire do I need to run and will it need a junction box to convert it to romex? Would it be best to add a secondary panel inside of the new build I would...
  8. Archie22

    How to wire two one gang dimmable switches and one intermediate switch ?

    Hi all, currently doing a job at a house where there are 3 switches In the hallway to control the hall lights. All 1 gang switches, one at entrance one in middle and one at exit, middle is an intermediate, other two are two way , the client wants all switches changed to dimmable. If I change the...
  9. D

    How to get wire back into connector

    Hi, I have accidentally pulled a wire out of connector (believe it is a molex?) I have seen info about getting the metal part out of the connector but only if the wire is still attached. Is there any way I can get the metal part out so I can reattach the wire? Thanks
  10. K

    Should outside earthing wire be covered?

    Hi All, I own a country Villa out in the Spain countryside. Was having problems with water pressure so local tradesmen advised to get a water tank and pump, he has installed this in the garage, and that has helped. However, the electrical circuit in the garage is an old circuit and wasn't...
  11. A

    Live ground wire throughout the house

    I have a live ground throughout the house. Is this dangerous and what are the possible causes? Thank you for your time.
  12. F

    Basement sub-panel wire requirements

    I’m running wires to the basement for future basement finishing. I’d like to add two circuits of outlets (one on the finished side and one on the unfinished side of the basement), baseboard heaters (I’m also open to other heating options, the basement stays in the low 60’s in the winter, so I...
  13. N

    LED mirror has double insulated symbol & earth wire - what are your thoughts?

    I recently bought a bathroom mirror with LED & Bluetooth speakers (from Amazon). There is a double isolated symbol on the back of the mirror yet there is also an earth wire connection. Is this unusual and should it be a cause of concern? It has not been installed yet - just wondering what your...
  14. ghostvaper

    How wire up/install 9 LEDdownlights

    I am installing 9 LED downlights each with an RGB bulb in (i will try attach pictures on them) - anyway I have been told that they need to be wired in a row. Like in/out - in/out in a ring pattern terminating at the last light. I am going to connect them to my wires where the old light fitting...
  15. will_505

    3 phase motor running backwards wire colours

    Hi all. Yesterday I wired in my 3 phase compressor to run off our 53kva generator. I just need to know which colour cable is for which phase as I'm not sure. Cables I've got are: brown, blue, black and green/yellow. I've currently got brown wired into live 1, blue into live 2, black into live 3...
  16. JodyCowart

    2 Wire Copper circuit in older home

    Without running new wire or at least ground, next best is GFCI receptacles for limited protection. I know about a bootleg ground to fool a tester. I am not going there! Does each receptacle need a costly GFCI or can standard receptacles be used down stream on the load side of the first GFCI and...
  17. D

    PL wire in wall no switch to turn off

    Hi New to this forum, Just looking for some advise as a DIY person. I have recently purchased a new home. I have come across a wall light which seems to be PL, and therefore always on. I have tried all switches in the home one by one and none turn it off, I cant see any switches nearby or fuse...
  18. finhudson16

    Seemingly under-rater MCB for wire size

    Hi All, I'm looking at installing an induction hob in my kitchen (upgrade from gas) and I gather that it can be added to the cooker circuit if there's enough capacity. In the fuse box and at the cooker end, the cooker circuit is wired in with 6sqmm cable, but only has a 16A MCB which I gather...
  19. Shoes70

    Issue with 12v wire LED conversion from halogen

    I purchased a house that has a really cool 12v halogen setup where two wires are suspended across the ceiling in two different locations, and each of which carries four 50W halogen bulbs. Each has a separate driver and dimmer. I first replaced the halogen bulbs with 8w LEDs, and they worked...
  20. T

    How can I safely join two ends of this wire?

    Thank you for taking a look at my issue. The pictured standing lamp had a foot actuated on/off switch which broke. I would like to join the wires. My first thought is to twist them together and cover with electrical tape, is this safe? Would someone be so kind as to suggest alternate ideas that...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top