On the instructions saying
Red to battery +12 v
White to ignition switch +12 v
Yellow to light switch +12 v
If these three wires connect them to the ignition switch +12 v will not work?
Hi,
I'm looking to get the lionshare of a small shed wired before a friendly electrician does the needful. I'm a confident DIYer, but I would appreciate any more experienced view to check my logic.
My house was professionally rewired in 2022, but I would like to connect a small 8x6ft shed to a...
Hello everyone,
How do you think reference method and type of wiring for flat twin and earth in non-metallic conduit will be :
just C and B?
Reference method B – Enclosed in conduit or trunking on a wall
 cheers
I'm trying to wire in a 4 core capacitive sensor into a safety circuit. I have brown, blue, white and black coloured cores and it's a NO sensor. What's the best way to wire this into a safety loop
I am an apprentice and the sensor didn't come with any drawings, the info on the sensor just say...
Hi guys, super basic question:
For a room layout like this, with my understanding that a lighting circuit downlight radial goes from one point to the next (whereas a socket radial can spur off in multiple directions), would this be acceptable, with the first downlight spurring off to feed two...
Hi all,
I have two questions regarding wiring and containment on commercial property stairwells in Ireland.
We are currently wiring a 3 story pub-to-be. We plan on using plastic conduit- surface from top stairwell landing to the bottom landing. I can't find anything to the contrary in the...
Good evening Sparks and Sparkles,
Has anyone got a wiring diagram for a storage combi boiler using a Hive (plumber says 1 channel...)...
The make and model are for some reason a closely guarded secret...
Many thanks
Hi Everyone,
New to the forum but hoping I can find a little help with my restoration project...
I am adding a secondary wiring "system" to my project car (username) to control add-on systems to include an electric fuel pump, electric radiator fan, fog lights and also to replace/upgrade the...
Hi all,
I am about to fit a light fitting and wanted some advice whether I should just connect the light cables into the correct terminal blocks or should I replace the terminal blocks with the Wago connectors?
I have attached a picture.
Any help would be really appreciated.
Sal9
Currently doing my 18th edition as its been so long since i did my 17th
just clicked on a Video saying DONT WRITE in the BOOK 😲
only in pencil, can i just rub it out!
Got Tabs and .. ive cut the book to make it easier to find the Sections
Hi, I was ironing and lost power to the bedroom and bathroom. All outlets and lights. I checked the box and reset breakers still no power. I called out the guy who comes to do electrical "new home still under warranty " and he came in bedroom opened light switch, i took these pics. He did...
Hello all,
I have a tail light for a '12 Ducati Panigale 1199 S, that I can't get working properly. The brake light / daytime running lights work fine through the factory connector. The turn signals are the problem, they do not work independently - they flash like hazard lights.
The tail...
Hi
I've been planning to fit an outdoor junction box at the front of my house to hide a large brickwork hole and properly house the wiring connections and was wondering about the wiring terminals I discovered.
Two outside lights are wired in and two separate terminal blocks are used to connect...
In July I moved into my new home with Schluter DITRA heated floors in the bathroom. The floor quit working in December, and my GC and a rep from the flooring company that did the heated floor install were here on Friday to troubleshoot with Schluter on the phone. I was home but in another room...
Looking to use this brooks Compton motor as a replacement in an electric cement mixer. can anyone tell me if it is designed to operate off a domestic single phase 240v supply? It looks to me as though it could run off either a single or threes phase supply but I’d be grateful to hear from...
Hi, Trying to wire this 3phase switch as single for a table saw, told I could do this from guy at Haymans, even told 2nd time which wires to connect, didnt work, other tradie at work couldnt work it out either. have L1 and L2 and N and T1 and T2 on bottom from diagram any help please?
Hello everyone, hope all are well.
I'm changing a ceiling rose and have lost the diagram showing where everything was connected (to the old light) and now I'm unsure on some of the wires. There are three cables, with three wires each: -
1 - Brown, Blue, Bare Copper
2 - Red, Black, Bare Copper
3...
Hi Everyone, hoping someone will be able to help me decipher the wiring for this hoist controller. the handset it came with has stopped working and I have purchased a new one but it uses momentary buttons instead of a rocker switch, I have sketched out what I think is the right wiring for it but...
Hi,
New to the forum. I have two very specific questions, for the setup below.
Setup details:
Currently I have a setup with an outlet used for my home theater (TV plug), an attic plug used for exterior cameras controlled by a wall switch.
I am now adding pot lights, to be controlled by a new...
I've pretty much sussed out the wiring for the radiators and underfloor heating, thanks to help from the forum. I do have one more question though. I feel the answer is obvious but i just wanted to double check.
In the diagram below there is a terminal block labelled manifold pump or valve...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc