working

  1. J

    Two 3 way switches, 1 reg, too many "extra" wires and zero working kitchen lights. (Picture Inside)

    Hey guys. Embarrassed to say but I've been living here for almost 5 years now and I've never had my kitchen lights working properly. Can someone possibly help me with some advice to wire these in properly? The other day I switched out all my old plug in outlets and light switches for new...
  2. acursi15

    Instrument cluster lights not working

    My 2003 Toyota Echo has two back lights in the instrument cluster. One of the lights would flicker if I hit a bump or something. I swapped the lights, meaning I put the bad light in the good light's place and vice versa, to help determine if it was an issue with the bulb or something else. The...
  3. B

    Ceiling fixture has only 2 out of 3 lights working

    Hi, I have replaced my ceiling fixture. The previous one had one light bulb and now I have put one that has 3 light bulbs. The problem that I have is that only 2 light bulbs are working. It was one light previously but since I have replaced the switch I've miraculously got 2 out of 3 working...
  4. C

    Two outlets in my garage are not working but no breaker has been tripped

    Both outlets are connected to a round pan box in the garage with a transformer on it
  5. Aaron b

    Isolating neutrals, working live?

    Hi, where only single pole isolation is achievable and a shutdown is problematic, what is the best practice with neutrals when connecting and disconnecting circuits? I understand that all live conductors should be isolated and we shouldn't work live, but out of the class room it is not always...
  6. markythesparky

    Self employed guy working for us doing work direct for our client.

    We have a chap who works for us a lot and who is self employed. We have found out that he may have done some work recently for one of our clients who we have not done anything for in about 6 years or so. Just wondered what your view is on him doing work for a client of ours, albeit 6 years ago...
  7. A

    Halogen potlights no longer working

    Hi everyone, I have 4 x MR16 (halogen) potlights running off of a switch. Model: IT2000M from Contract Lighting Contraste - IT2000M - Remodel - https://www.contrastlighting.com/Housing/IT2000M?lang=en The other day, there was a humming which I believe was coming from the electrical panel and...
  8. G

    Magnetic lock timer not working.

    Tried fitting a magnetic lock on a job for a bathroom. Client has had problems with people doing drugs in his bathroom so wanted to control entry from his shop tills so the lock is fitted and works but I need it to be sorta timed as when releasing, the button locks the door( staff can't use the...
  9. D

    Why Is Light Not Working?

    I have two matching front room lights that are operated by a 2 gang dimmer switch. The right light operated by the right button has stopped working. The left one is fine. I can't figure out the problem. Help would be appreciated. I've swapped the two lights (the entire fixtures and bulbs) and...
  10. littlespark

    Working in your own gaff when things don’t go to plan

    Spent yesterday morning running a spur in my kitchen from one double socket on the rfc to a new one along the same wall. Original socket is just beside the multi gang grid switch for appliances. More on that later. Wife came home from shopping with the birthday girl, ranted at me for not doing...
  11. D

    Outdoor lights not working

    I have 2 double outdoor led lights on a dimmer. Over xmas the lights flickered then went out. I thought one of the wires came loose, i checked all connections, all ok. Will a faulty dimmer cause this? or is the power board likely to be the problem? A bit hard to get a sparky at this time of...
  12. G

    Light switch not working when fitted to the wall

    Hi all Can anyone please advise, i have fitted a new fused light switch cover in the kitchen as the press switch part broke on the old one, however I wired the new one up and all worked well, but when I screwed it back onto the wall it would not work, took it off the wall and it worked again. 🤯
  13. U

    Quantum heater top vent not working

    I've got a QM150RF in the living room. The bottom vent is outputting hear fine. But the top vent seems to not be working over the last day or so. Is this a fault or part of it's heat adaptation?
  14. C

    MR11 -12V spot lite not working with 12V wall adapter

    Hi all, Im back here again. i have a couple of R11 12Volt 20Watt G4 Bi-Pin Base bulbs tha i salvaged from a backup lighting unit. I have tested them on my car battery and the are working. I would like to use one in my house as a spot in my stairwell area. So i have tested it eith a 12V 2A wall...
  15. T

    Going it alone after a lifetime of working for the man!

    Hi Team! I am a 46 year old electrician and have always been a subbie. The day my apprenticeship ended, I became self employed and have worked on industrial or commercial sites all over England, largely through agencies on a monkey see, monkey do basis. Kind of "There's the cable, there's the...
  16. G

    Xmas lights not working - replacement adaptor needed?

    Hi there, Wondered if someone could advise as not good with electrics! I have an expensive Xmas tree which is pre lit. It decided not to light up a few days ago and not really sure what the problem is. I thought it may be the power/ transformer plug but can't seem to find a replacement...
    • GreigM
    • Thread
    • adaptor lights needed not working replacement working xmas
    • Replies: 10
    • Forum: UK Electrical Forum
  17. B

    UK Kitchen extractor hood fan not working?

    This Candy CCE16/2X kitchen extractor hood fan is not working, the lights are still working but the fan itself is not. I know there’s a fair bit of grease on there as you can see but will that be the cause & are there any other things I can check myself to find out why?
  18. D

    New LED canned lights not working

    DIY question: I tried to replace my kitchen can lights with LEDs. The old light fixtures were just two wires connected to a fixture. I removed the screw in connector on the new light fixture and connected the wires. The lights are also dimmable and on a 3-way switch so I bought a dimmable 3-way...
    • Deleted member 143810
    • Thread
    • led lights new not working working
    • Replies: 3
    • Forum: Lighting Forum
  19. J

    UK Horstmann Electronic 7 only working with boost, not timer

    Hi, We have just moved into a new flat with the old Horstmann electronic 7 timer for our immersion boiler. We just moved from a flat with the exact same system and never had any issues. We have set the timer and the times for the off peak boiling and have had no hot water for 3 days. The boiler...
  20. O

    Subaru Power Seats Issue -Gets power but not working.

    Hi All. I am retrofitting seats into my Subaru Impreza, from a legacy. The new seats are electric and were working fine coming out of the doner car. There was an existing unused wire under my seats so I connected that to the new seats. Its showing that there is 10v getting to the connection...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Back
Top