Meter Tails 16mm 0r 25mm

[haj]

Talking with a collegue today regarding meter tails.I went to look at a c/u change 80A main head on 16mm Tails i said should be 25mm but he said 16mm was ok 25mm for 100A main head. Whats the word out there with you good men ?
Cheers

 

[chocolate]

Always go for the better option with cable sizes. I would personally never use 16mm whatever the incomer fuse. Even if you know it's 60A or 80A, pretend it's 100A and put in 25mm2 tails ( double insulated ). The 17th Ed. recommends that anyway whatever.

 

[flukey]

i only fit 25mm

 

[securityvillage]

As previously stated 25mm for me too.

 

[haj]

Thanks guys i quoted OSG it says SHOULD be 25mm not must be 25mm he says leave them alone i think change them.

 

[flukey]

Thanks guys i quoted OSG it says SHOULD be 25mm not must be 25mm he says leave them alone i think change them.

quite right haj, exact wording is

"polarity should be indicated by the colour of the insulation and the minimum cable size should be 25mm2"

theres 2 shoulds in that statement. would your mate ignore the first should the sameas he would the second should

25mm it is then

 

[garyp1155]

Talking with a collegue today regarding meter tails.I went to look at a c/u change 80A main head on 16mm Tails i said should be 25mm but he said 16mm was ok 25mm for 100A main head. Whats the word out there with you good men ?
Cheers

hi i assume that it was a house you went to so has to be 25mm .also double insulated hope this helps.

 

[Peter Woodford]

Do you get leb in to pull fuse or are we aloud to disconnect from there meter

 

[SirKit Breaker]

I always use 25mm tails, just remember to upgrade the bonding cables to suit.
The meter tail size is dependant on the cutout fuse rating as far as i `am aware.

 

[Mac]

Do you get leb in to pull fuse or are we aloud to disconnect from there meter

Just do it.Pull the fuse.Who says there was a seal on the cut out anyway

 

[philsheriton]

You are supposed to get them to pull the fuse (its their equipment) but i always do it my self problems start at the main fuse if youre up rating the tails from the meter to the consumer unit then you should also change them from the incomong supply point ( the fused inlet)Probably stating the obvious burt rememmber the meter is wired live neutral neutral live good luck you obviously can't seal the job but to be honest most work i come across the meter is never sealed any way good luck phil S

 

[ajelec10]

Do you get leb in to pull fuse or are we aloud to disconnect from there meter

Peter if you are in any dout as to weather to remove the suppliers cut out. dont be. Basicly the electricity at work act says that every installation has to be provided with a means of isolation for safe working. So if the supllier has provided a means of isolation ie a swich or the meter with a built in isolator (not designed to be switch under load) then all is fine but if they have only provided a cut out and meter then they can not argue why you have cut their seal and removed the fuse. what do they expect you to change the tails LIVE!?????
Hope this helps
Regards
AJ

 

[haj]

Thanks gentlemen as far as pulling the cut out as said earlier JUST DO IT we need to stay safe dont we 25mm & 16mm earth it is then !
I digress i have been asked to wire a loft conversion my questions are is it ok to extend the upstairs ring and lighting or should i take a couple of new direct feeds from the board not so easy but possible i think.Do i need to beware of any regular problems that pop up with loft conversions ?
Cheers Guys

 

[Risteard]

what do they expect you to change the tails LIVE!?????

No, they expect you to contact them to remove the fuse.

Interfering with the Supplier's equipment is illegal and is subject to a Stg £1,000 fine.

 

[ajelec10]

Yes in an ideal world, but its just not reasonalbe practicable is it. so you are a good boy and phone them every time you want to change some tails and you sit around waiting for them to pop out and do it for you. Don't think you would win many jobs if you are chargeing on the costs??. They have obvsioly seen a problem with the old units and thats why now they install either a swicth or the meter with the isolator built in.
Many Thanks
AJ