Search results

Search results

You will need 50 posts under your account before joining in with this thread because you can't link out without 50 posts first.

  1. Diytim

    anyone know of a white surface mount 2 gang box

    Use a pvc box which doesn‘t shatter like the plastic ones and drill a 20mm hole in side as required.
  2. Diytim

    Plaster board faced insulation - making good?

    Screw a piece of battening across the hole you have made with plasterboard screws either side and countersunk. Then cut a piece of plasterboard the correct size to fill the hole you have made and screw that to the battern. Finally skim over joint with plaster or filler as appropriate.
  3. Diytim

    Covid Shielding and Rewire.

    No, these are recommended only.
  4. Diytim

    UK EICR Done, New CU Required. Am I being taken for a ride?

    Regs are not retrospective, as others have said if it was ok at installation it should be ok now. Now if you want to upgrade to the latest spec for increased safety that’s a different job. But bear in mind that a good CU can be obtained for under £100 so the rest is all labour which sound expensive.
  5. Diytim

    UK Running a cable for home Welder

    Don’t forget you will need an Earth stake outside the garage connected to your new CU.
  6. Diytim

    Insulation tape on connector blocks

    You are right! I think it’s belt & braces just an extra layer of protection in case some odd wire may touch one of the screw terminals or to hold the cable in place with the missing cable grip.
  7. Diytim

    3 phase supply to single phases only 2 phases used

    One problem I got an emergency call out on a strong windy night where lights were going up and down and dist board smoking. On investigation I found we had lost the neutral supply and 480v was being applied to the household single phase circuits. Had to pull the main cut out fuses and inform the...
  8. Diytim

    changed door issues with locking and airbag light

    Check all your fuses, you did disconnect the battery before starting work didn’t you!!?
  9. Diytim

    Henley Block between meter and main switch

    Do a risk assessment first before working on live equipment. Is there a safer way of disconnecting, Yes ! Remove the main fuse on no load. As far as I know nobody has been fined for removing the fuse as long as you are not trying to steal electricity.
  10. Diytim

    Insulation tape on connector blocks

    choc blocks are screw connections and such should be accessible for maintenance & testing in the future. Do not bury in the wall where nobody will know they are there. All cable runs must run horizontal or vertical from accessories to accessory.
  11. Diytim

    Terminating armoured in meter box

    With this arrangement I don’t see how you are earthing the steel wire armouring?
  12. Diytim

    Why does the UK use rings for sockets?

    Depends on the number of sockets required. One or two sockets radial are ok but larger cable required. You can have any number of 13 amp sockets on a ring circuit as the floor area is the limiting factor. Use 2.5 t&e in a ring and wired back to a 32 amp breaker will prevent overloading circuit...
  13. Diytim

    What electrics are required for water underfloor heating?

    Hi , I installed a complete underfloor heating system myself and it’s not too bad. What will be required is the controls for each circuit. Assuming each room will require its own circuit or two there will be a manifold somewhere where all the individual underfloor pipes come together. Install a...
  14. Diytim

    two shaver sockets

    Hi, if both of these shaver sockets are proper ones with built in isolation transformers then I don’t see a problem as there will be no potential difference between them and hence no safety problems.
  15. Diytim

    3 phase supply to single phases only 2 phases used

    Hi I have a customer on an old farm supply. Many other electricians have assumed it was just 2 of 3 phases supply but it’s not. I learned about farm supplies from my tutor at technology college 50+ years ago who worked for the local supply company. They used the 2 phases for farm machinery...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top