Met landlord on site as he lives not far away and showed him which filters he needed so he could see for himself.
Cooker is on inside wall of a ground floor flat and only possible route for external ducting across top of wall units is impeded by the boiler flue, so it has to be recirc...
Ok guys, after a visit to the job I can confirm the fan contains no oil as it's just a dry motor inside a dry casing. The oily substance was actually from airborne grease in the open plan lounge/kitchen coming from the recirculating cooker hood extractor! There were no charcoal filters fitted...
Thanks for all your replies.
Just to clarify, it was me who cored the hole out (from outside) and it was cored out level not on any slope (ideally I wanted to slope it downwards to outside but the fan spigot is 4" deep and wouldn't have fitted into the duct if sloped so had to be level).
I...
Hi all. Has anybody else had an issue with installing a wall mounted 4" extractor fan, only to find after 9 months the customer has contacted me to say it is now leaking an oily substance down the wall and ruined the paintwork.
I am happy to replace the fan free of charge as it is within the...
Thanks davesparks. Looking at the diagram on the driver that's what I interpreted too, but I heard somewhere that the DALI system doesn't like 230volts, so I didn't want to try and blow the unit! However, I have now heard back from the supplier and they have confirmed what you said, so cheers...
Hello all.
I have recently installed 3 of these lights
https://www.directlightingsupplies.co.uk/product/dimmable-leda-6ft-twin-led-60w-batten-cct-switchable-colour/
in a large garden office for a customer.
He wants them dimmable and I have pre installed a 2 core 1mm flex from the switch...
Hi all. I have a small question about inspection interval labels.
We all know to fit one of these labels with the relevant date upon completion of a new installation, CU replacement etc, and upon a "satisfactory" EICR.....but what about an "unsatisfactory" EICR? Do you guys still fit a new label...
Slightly going off landlords, It always amazes me that these EICR "inspectors" have the audacity to cut so many corners during an inspection. I understand that time is money and all that, but how do some of them sleep at night.
And how don't they get found out?
I would be worried if my...
I was tempted to do as timhoward mentioned to get the water heating up again, but you know when you get a bad vibe for a bad landlord and a job you don't want to be associated with.
I have a card reader, but that's no good when the landlord isn't on site and says he will "drop the cash off...
Has anyone had encounters with rogue landlords?
I will tell my short story (and keep it as short as possible)
I had a call a few weeks back from a landlord to sort out an issue with an immersion heater following an "incident".
It seemed an emergency so I arrived that afternoon and the tenant...
Has anyone on here using the Napit Fast test software for EICR's noticed that in the section "Extent and Limitations of Inspection and Testing" there is a box marked "Extent of Termination Sampling" which needs to be filled in.
This must be a very recent addition, or it's been longer than I...
Sounds so simple when you put it like that.
I think i was overthinking it and doubting myself and getting mixed up with the fact that the lodge doesn't come under planning consent.
Now I feel a ---- for asking such a simple question!
Cheers
I have just completed a (large) new build timber lodge in a customers (large) rear garden and today given it a full test and produced an EIC for it.
The owner says he has not needed building control/planning consent as it is just within the criteria to not need it, even though it is a 4 bed...
Would have to agree with UNG. It's probably the easiest way to ensure (not guarantee) that a call to the DNO to replace the main fuse would not be needed during busy peak times.
New consumer unit needed is almost certain as it's more likely to currently be rewirable fuses or at best 3871 plug in MCB's.
What about the 2.5mm T&E cable for that era...didn't it have 1mm CPC? Could that tip the max required Zs readings of some circuits over the edge?
Also tails, main earth...
Thank you all for your answers.
The general majority seems to favour leaving the storage heaters on the 20A DP's so I think I will go with that as it will keep the customer happy with a clean bill of health on the EICR, I will sleep better knowing all is ok, and it means I don't need to do a...
Done a few EICR's recently and having a blonde moment regarding storage heaters.
All storage heaters in the property are rated at 1.5kw and fed by 1.5mm HR flex, circuits are individually fed in 2.5mm T&E by individual 16A MCB's.
All perfectly normal, except that each one is isolated locally...
Thanks westward, I suppose it makes sense otherwise the old amendment wouldn't even be an option to use on the Fastest software.
So I guess until 28th Sept I can ignore the fact there are no AFDD's on socket outlets (or SPD's due to the mains powered smoke alarms) in a HMO then? and using the...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc