Search results

  1. R

    Scantronic tags restricted number range

    Never had this problem before, if they are not official Scantronic tags then they well be in the wrong format to operate the reader.
  2. R

    Accenta alarms (explain keyswitch and set to an idiot)...

    On the Accenta six, you could wire your relay coil between the set output (+ve) and the bell B terminal (-ve), then the relay would only trip if the system is set and the bell rings
  3. R

    Accenta alarms (explain keyswitch and set to an idiot)...

    On the G3 panel wire your relay off the INT communicator terminal, that will prevent sending a signal if the strobe is tested. The keyswitch input would work with a relay output triggered by the app.
  4. R

    Accenta alarms (explain keyswitch and set to an idiot)...

    The keyswitch zone will set and unset programme one without using a code, you would need a boxed keyswitch with a tamper switch in order for it to work securely, or a shunt lock (normally a Chubb lock fitted with an internal microswitch) The push to set is used to terminate the exit time once...
  5. R

    Aritech CS350 Open Zone

    The resistors are in the right terminals, it looks like in the first picture the blue/white wire to the second detector is not connected to anything, try connecting it to the white wire that it is twisted to. Can you post a better picture of the first images terminals, I am finding it hard to...
  6. R

    Aritech CS350 Open Zone

    The Aritech CS350 works with end of line resistors, if you connect a 4K7 resistor across the zone in the control panel it should show closed, if that works then you have either a cable fault or the detector wiring is wrong.
  7. R

    Obsolete Timeguard PIR

    I have used these many times, and not had any problems, they might get you out of trouble. Spectra Wirefree PIR & Receiver Kit - Black -...
  8. R

    Accenta Optima Compact PA Disconnecting

    Hi, you will need to put a jumper in the panel across the PA terminals in order to continue using the system.
  9. R

    Galaxy Alarm Tamper Keypad

    The keypad tampers can be troublesome, especially on an uneven wall. Make sure the keypad is correctly clipped on to the wall mounting plate, and sometimes a few layers of insulating tape on the tamper peg helps.
  10. R

    Risco wisdom wireless alarm

    Is the entry unset menu option in parameters set to yes, if so this needs to be programmed as no to enable the alarm to be unset during the entry time.
  11. R

    12v AC door release conundrum

    Hi, I have used lots of these in the past, they operate on 12-24 Volts AC/DC and can be tripped by a normal door release push button switch....should be ideal. DIN boxed universal timed relay - Videx Security -...
  12. R

    keypad door entry: door won't open.

    I agree, I had one last week where the relay contact had welded itself together, the installer had not fitted the transient suppressor supplied with the lock :nonod:
  13. R

    9.5Kw Shower Installation

    My money is on the switch being incorrectly wired, as the neon only illuminates under load. As stated previously check the switch wiring and in case of any doubt isolate the circuit at the CU and await the arrival of your qualified electrician.
  14. R

    Shed Supply

    Looking at the picture it would appear that the busbar is disconnected :uhoh2:
  15. R

    scantronic 9800

    Hi, the bF fault code is only for the internal control panel battery, have you disconnected the mains and checked the battery voltage on load ?? The external sounder battery will not be monitored by the control panel. If the circuit board is not charging the battery, the circuit boards often...
  16. R

    Alarm door contacts Help!!!!

    One important factor in this thread is in my mind, the fact that a tamper loop on the door contact provides double pole protection to the device, if an attempt is made to short out the wiring to prevent the contact from working, a fault condition will be generated. A single pole pair to the...
  17. R

    Bt headscratcher

    Hi, each incoming BT line is only a pair so it is common for a property with more than one line to share a cable, pair one being blues, pair two oranges, pair three greens and pair four browns. In properties fed by overhead drop wire, the practice is also common, orange and white being the...
Best EV Chargers
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Advert

TrueNAS JBOD Storage Server

UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
JBOD Forums: a forum for JBOD storage server advice
JBOD Suppliers: JBOD Storage Server Supplies
Back
Top