disconnect

Recent contents Top users
  1. N

    Testing Help

    Hi guys starting a new job testing commercial properties, i have passed my 2391 a few years ago and im just looking to refresh myself< 1: when doing an IR test on circuits protected by rcbo's to i have to disconnect both neutral and earth flying leads? 2: what are the flying leads on rcbo's...
  2. P

    Insulation Testing Conundrum

    Hi Guys Domestic - Old Hager Box 14 MCBs RCD Main Switch. Totally stuffed with wiring - not keen to disturb Tested the Full L+N busbars to E. IR = 1.8 Meg b****r! So close to 2 Meg! Tried L busbar to E -all trips off. 1.8 Meg!!!!!!!!! - had to disconnect RCD! Tried each cct in turn L to E...
  3. Y

    IR Testing

    Hi All, Firstly I'll apologise for not trying to collate this with another thread, But thanks to my organisation skills I find myself short on time. I'm currently at College and coming up to a assignment to do with testing etc. I understand pretty much all area's of testing, However theres a...
  4. F

    IR Testing lighting cct with fixed bathroom extractor load

    Domestic CU change, TN-C-S. Lighting circuit has an Extractor Fan with Electronic timer installed. When performing IR test on the lighting, should i just test the whole lighting cct between L & N (connected together) and the CPC - I do not want to remove the cover of the extractor to disconnect...
  5. P

    RCD test button

    If an RCD passes the manual push button test, is this any indication that it will disconnect in the required time under actual fault conditions?
    • PB1
    • Thread
    • aus before button disconnect electricians' talk fault rcd test tests
    • Replies: 10
    • Forum: Australia
  6. M

    Student doesn't understand disconnect times

    Why do circuits over 32A have a 5s disconnect time yet those 32A or less have a .4s disconnect time? I have read the relevant regs but do not understand why and cannot find the answer in my books
  7. R

    Testing help

    Morning all! Just completed my two jobs for my NIC assessment. Confident in my work and all of my test results etc. Anyway assessor had a cancellation so has booked me in for this friday so just wanted to double check a few things that are playin on me a bit. Nothing major but just wanted to...
  8. I

    What to charge to disconnect and replace 4 lights

    hi there have a possible job customer wants 4 light fittings changed and replaced. circuit will be Tested and Minor Cert issued. Customer supplying light fittings. i usually charge £ 30.00 so would £120 sound fair ?
  9. L

    Can anybody think of a good reason for the DNO to disconnect TNS with Ze of 0.25ohms?

    Whilst looking at the supply intake at a house rented by my mate I noticed the Main earth which was clamped to the sheaf of the supply cable was disconnected, the service head is a TNCS, the main earth from each small 3036 CU goes to this head as well as the two main bonding conductors...
    • LlandrilloSpark
    • Thread
    • anybody aus bonding disconnect dno earth electricians' talk reason supply
    • Replies: 3
    • Forum: Australia
  10. T

    RCD's

    Hi people, Can any tell me what would make an RCD take a long time to disconnect, i understand they monitor the line and netural wires but what would make them take a long time to disconnect or not even trip when testing. Many Thanks.
    • Tencho1234
    • Thread
    • aus disconnect electricians' talk rcd rcd's
    • Replies: 3
    • Forum: Australia
  11. B

    What qualifications do i need to disconnect or re-connect a three phase supply

    I install ovens into large supermakets, within the bakery area, and sometimes these units are hard wired, most are three phase, some are single, upto 100amp supply, i have been told the installation and testing cert is needed, but we would not change the supply, only exchange the machine for the...
    • borgmaster
    • Thread
    • aus disconnect electricians' talk phase qualifications supply three three phase
    • Replies: 5
    • Forum: Australia
  12. L

    Disconnecting a 3 phase compressor

    Hi all, I've just been asked to disconnect a 3 phase compressor. Not having done this before is it just a case of power off, disconnect then power back on or is there something special I'm missing out or need to consider? Regards.
    • lish70
    • Thread
    • 3 phase aus charge compressor disconnect electricians' talk phase registered
    • Replies: 12
    • Forum: Australia
  13. M

    Advice appreciated Radial/Ring Circuits

    I have a customer with a 4 double socket ring main on a 32Amp MCB in thier Snug, R2 and RN are all Good but R1 is open Circuit. The CU has a 100mA RCD on A TNCS (need to change it to a 30mA) the house was refirbished about two years ago and dont think the builder got in a proper Electrician...
    • mos
    • Thread
    • advice appreciated aus circuit circuits disconnect electricians' talk radial socket
    • Replies: 2
    • Forum: Australia
  14. W

    Dead Testing - 3Phase Motor and S-Plan

    When testing Insulation Resistance or Continutiy on a 3phase Motor, do you need to disconnect the cables from the motor? Or do you just test I.R to the starter, then I.R from starter to motor? (as the starter will be open when dead) Would a motor come under "equipment vulnerable to testing"...
  15. B

    RCBO achieving 40ms disconnect only when phase reversed

    Howdi I have a 32a ring that when I test the RCBO it won't achieve 40ms when tested at 5x in 0 degrees but when switched to 180 degrees it trips well within 40ms The Zs measured is 0.49 ohms the circuit trips at 1x okay so Im a little confused and am looking for help to point me in the right...
  16. R

    Testing Zs - disconnect main bonding or not ?

    Hi When measuring Zs on circuits do you guys leave the main bonding connected or disconnect it? Most of my testing books including GN3 say leave it connected, but another book by Anthony Hinsley says to disconnect it as it will introduce parallel paths (which I get) and that if left connected...
  17. C

    Problem with Power Cabinet blowing fuses

    Hi there, I have a ----y problem as follows: I have a ABB disconnect switch Fused at 60A, supplying 3 phase 575V(North America) to a Power Cabinet. The Power Cabinet has several motors and a 6000VA transformer, that steps down the voltage to 230VAC/120VAC single phase. The Cabinet...
    • collin1443
    • Thread
    • aus blowing cabinet disconnect electricians' talk fuse fuses power problem transformer
    • Replies: 2
    • Forum: Australia
  18. Mark.W

    Minor work IR

    Chaps I replaced a single socket for a double socket for a customer today, and whilst doing the IR tests noticed that the Line/Neutral reading was low. The readings were: L/N 0.95 Mohms L/E 97.6 Mohms N/E 87.4 Mohms I checked and made sure that nothing was plugged in on the ring and noticed...
  19. R

    Testing floods with P.I.R's

    When testing IR on a circuit spplying some outside floods with built in pir's, Is there any other way other than disconnecting the p.i.r in the fitting's?
  20. M

    Neutral CPC short circuited in PME system, is that correct?

    HI Doing a test with a voltage detector/continuity tester on live PME/TN-C-S system installation at a socket outlet either with load and without the load shows voltage between live and neutral and live and earth but live-earth seems to be short circuited and the continuity tester indicates...
Best EV Chargers
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

TrueNAS JBOD Storage Server

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.
UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
JBOD Forums: a forum for JBOD storage server advice
Back
Top