induction

  1. O

    UK Should I be worried? Induction hob installation

    Last night I was cooking dinner on my induction hob. While I had my back turned to the hob I heard a lot of crackling and popping and then smoke started coming out of the master switch for the hob on the wall. It stank for fish.... It was kind of scary to have to touch the switch that was...
  2. R

    Replacing ceramic hob for induction - basic questions

    Hi all, planning to replace my electric ceramic hob for an induction one. Current ceramic hob is: Baumatic B12SS - 230v/400v 3N 50/60Hz 6kW 26.1A, min fuse protection rating 30A. The current setup is as follows: CCU>1xB32 MCB>connected to 2x red cooker switches: Switch 1: connected to hob...
  3. C

    Separate feed for Cooker and Induction hob

    Evening gents After a quick question about a kitchen rewire (Im an industrial electrical engineer, not been a house basher for a good 15 years) Im moving the cooker from one side of the kitchen to the other and running a brand new supply from the consumer unit. Im also moving from Gas hob to a...
  4. M

    Single phase induction motor schematic

    Hello, I've found an old motor originally designed for operating jealousies. Could you help me read and better understand the following schematic? As far as I understand, it is a single phase induction motor, there is 47 uF capacitor connected to it in order to start. There are 3 contacts...
  5. E

    Wiring terminal block for induction hob

    Hello...I need to rewire a terminal block for zanussi induction hob zei6840fbv Can someone help please. ImGe attached
  6. B

    Induction hob.

    Am about to install an induction hob and can either use single phase or three phase. Will use singles in conduit. Maximun load is 11Kw so either single phase in 6mm or 3phase using 2.5mm. If I use 3 phase I will get a normal cooker isolation switch to operate a 4 pole contactor, as am not too...
  7. J

    Induction Hob & RCCB

    Would appreciate your thoughts on this please. Wylex split load consumer unit with one rccb, new circuit installed for induction hob on non rccb side with 32 amp rcbo. When the hob is switched on the rccb trips, not the rcbo. The circuit has been tested out and is fine and the neutral for the...
  8. A

    13amp plug for 3000w induction hob

    Hi all, I had a look around and can't seem to find anything regarding my specific issue. We use 240v We bought a new induction hob, it's a Brandt BPI-6410B and is rated as 3000w / 13amp and has wiring as below. We had a Bosch PIN675N17E/01 rated at 7200w which died. It was wired to a round...
  9. G

    Yet another induction hob question

    Hello I have a new AEG induction hob rated at 7.4kw max using power sharing but AEG do not specify a cable size or mcb rating nor will they answer the question I submitted to them by email. I think their position is that it is down to the electrician to decide. The configuration is as follows...
  10. D

    Induction hob and oven fitting

    HI I want to fit an induction hob and separate oven. The supplier says the hob (7.35kw) needs a 30A supply and the oven (3kw) needs a SEPARATE 13A supply However a stand alone cooker with induction hob is specified as 11.3kw (which is approx 45A) and it states that it needs a 30A fuse. My...
  11. H

    Induction Hob - Safe to use existing cooker circuit

    Hello Forum, I need to replace the hob in the kitchen as it is faulty. I would like to be able to use an induction hob, so I need to make sure that the wiring and mcb on the cooker circuit is the right specification. The combination Oven (1 small / 1 Large ) has a Max load of 4.1Kw. The...
  12. D

    Using an Induction Hob and Fan over at Same Time

    Hi, I have a 1800 watt induction hob and 2300 watt fan oven. Both use 13 amp plugs. Are they using too much power to use at same time? Thanks for reading
  13. V

    Induction cooker hardwiring 32amp

    Hi All, We are in the process of replacing our gas hob to an induction hob (7.35 KW, 32 Amp). Our electrician suggested that we get a radical circuit terminated at a 32 amp RCBO. There are currently double pole switches for exhaust and washing machine hanging from another ring main. Our idea is...
  14. J

    Strange design of Induction Hob power input, advice please

    Hi, hope everyone is enjoying Easter! I have boon looking for an induction hob recently and found one on ebay for £25 and close by so I bought it, yay!. It was purchased as defective, its a 5 sone hob and the two left zones did not power up. A bit of research before purchase shows there were...
    • jaytee
    • Thread
    • advice design hob induction induction hob input please power strange
    • Replies: 23
    • Forum: UK Electrical Forum
  15. S

    Install new oven & induction hob to existing circuit

    Hi All. Just a little help I need connecting a electric oven and induction hob. The existing is a 32 amp MCB in the consumer unit. A 4m run of 6mm sq t&e cable from mcb going to a 45A cooker control switch. From here a 6mm sq t&e going into cooker connection unit. I have removed the old electric...
    • Steve D
    • Thread
    • circuit existing hob induction induction hob install new oven
    • Replies: 35
    • Forum: UK Electrical Forum
  16. Cupa

    Wiring up an induction hob - wanted to sense check if what I'm doing is correct

    Hi guys, I have a new induction hob which I'd like to wire in. I have already wired in the oven and grill into the kitchen using a length of 4mm 3 core heat resistant flex and that is working fine. Back of the hob shows the following diagram: Based on the above schematic, I plan to wire in...
    • Cupa
    • Thread
    • check correct doing hob induction induction hob sense wanted wiring
    • Replies: 23
    • Forum: DIY Electrical Advice
  17. D

    Gaggenau induction hob fault - code Ci9 ADB R

    Gaggenau induction hob fault - code Ci9 ADB R Today, 08:29 PM Dear All, Does anyone have any experience of the induction hob range made by the company Gaggenau? I have a customer who has the above fault being displayed and now the hob after struggling on and off for a few months has finally...
  18. A

    11.1kw induction hob

    Need a second opinion. Wiring 11.1kw hob with a cable run of 50m usually I'd say 10mm t&e but something in my head tells me I should be upping the cable size
  19. Spark40

    Another induction motor question

    which factors might affect the slip and what losses may be incurred by the motor ? Cannot find much about this, i know that the load indirectly affects slip due to the rotor speed changing, more load is more slip Any assistance is appreciated, thank you If any websites is found in referance...
  20. Spark40

    Induction motor question

    what is the affect on starting current and torque of changing the electrical supply frequency? I can find out that the speed changes etc from this website: Changing an Induction Motor's Power Supply Frequency Between 50 and 60Hz -...
Best EV Chargers
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Advert

TrueNAS JBOD Storage Server

UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
JBOD Forums: a forum for JBOD storage server advice
JBOD Suppliers: JBOD Storage Server Supplies
Back
Top