out | Page 5

out

Recent contents View information Top users
  1. M

    Boxvan LEDs shorting out? Grounding out?

    My box truck has interior lighting in the box and its wired directly to the fuse box (blue wire at bottom of pic). The interior lights are also connected to the front marker lights somehow. After months of it being fine, it went haywire last night and now they're shorting out the ignition and...
  2. R

    Callender main cut out and main earth

    Morning all, Just after a bit of knowledge!! Been to a job to move a light switch. When I got there noticed a callender main cut out . The incoming cable is enclosed in conduit and main earth has been bonded to that. The conduit looks like it goes straight through wall into next door as it is a...
  3. Chapperz

    Belling out

    Stupid question probably but... If someone was to bell out a circuit to find a fault, should they disconnect from the board and why? Also, if a light on a two way and intermediate stays o. Perminately would that be due to the strappers being mixed up? Thanks people Regards
  4. M

    Latching relay chattering.

    Can you supply a latching coil through it's own set of NC contacts? Or would it try to drop out as soon as it tries to pull in.
  5. H

    2 sockets working out of 5

    Hello I have added 5 sockets to a double socket the double socket in the annexe has a 2.5 armoured cable added which goes down to the summer house before going in the summerhouse it runs. A water feature on an exterior fused switch then goes in to the summer house where the first...
  6. HappyHippyDad

    What is going on with this cut out and the neutrals.

    I have just (kind of) completed an EICR. It was the worst house I have ever been in. They are horders plus the house was filthy. I was unable to get to certain areas. I realise there are a number of fails (c2's) with the picture but my question is regarding the 2 x 10mm tails coming out of the...
  7. T

    Why does new 1700 watt microwave keep burning out my 20amp dedicated breaker?

    20amp outlet, 20amp breaker, 14 gauge wire. I suspect I need a larger wire but that’sa lot of trouble to go through without being sure.
  8. S

    UK Swap out Extractor Fan

    Hi all. I’m looking to swap my old noisy bathroom extractor fan for a new one and am after some advice on the wiring. My old one is on a timer and comes on with the light, turns off after around 2 mins. The new one doesn’t have a timer (it’s next to a bedroom and just a toilet). The wiring...
  9. P

    Induction hob and oven not working properly

    Hi guys here is the situation,switching all 4 heaters in induction hob(7.4kW)and it stops working.Taking out the oven (2.5kW)which is just underneath and find out that hob and oven are both plugged in to double socket.There is no cooker connection unit but there is cooker switch above.From the...
  10. I

    No bonding, no work getting carried out?

    Evening all, My NIC inspector told me years ago "if there is no bonding in place, you're within your rights to switch off the electrical installation until works have been carried out!".... not sure if this is true? When asked by a customer to carry out a job which you give a cost for before...
  11. T

    Does anyone have any literature regarding Inspection Schedule on an EICR which would help to fill it out correctly.

    Thanjs
  12. A

    2 way dimmer and JCC V50 cutting out

    Hi guys, just installed new JCC V50 down lights with two 2 way brushed brass dimmer switches from Knightsbridge. When I turn one of dimmers up fully it cuts the light out. And then sometimes they flicker on start up… then if I have one switch dimmed to the lowest and the other is switched to the...
  13. L

    DISTANCE from D/G socket to max reach of pull out kitchen tap ?

    Distance from D/G socket to extended pull out kitchen tap ? Kitchen tap when pulled out is easily with 400 mm of a D/G socket . Not my job . Just asking for clarification etc
  14. Gavin John Hyde

    Amendment 2 coming out next year thoughts?

    Just been reading an article regards Amendment 2 coming out next year. The requirements for AFDD is going to create some interesting conversations with customers as they are not cheap. Unless manufacturers get their act together I would be surprised if in 12 months they have stock or are...
  15. F

    Dash Lights Out... Add Rheostat for dimming

    I have a 2005 Honda Odyssey that has dash lights that are a combination of LED and incandescent. Most of the incandescent lights do not work. That results in my radio backlight and most of the buttons being off. I have tried to track down this issue and haven't found it. The factory dimmer...
  16. Anthony Deakin

    How to work out no value of Zs to Ze being 0.35 ohm

    Hi all, ive been asked this question A direct measurement of Zs cannot be carried out. The supplier gives a Ze value of 0.35 ohm and the line and cpc resistance as 36.24 milliohm/m. If the circuit is 31metres in length the earth fault loop impedance will be? What is the formula please? Thank you
  17. D

    Cable out of the wall and back in

    Could I run a low voltage cable that comes out of a stud wall and back in again 50mm later to get past a stud. I don't have access above that part of the wall. It would be covered by a cabinet but of course if seen it would look very dodgy. I was thinking of labelling the cable at the very...
  18. dlt27

    2 supplies to property and the one trips the other out!!

    Hi, thanks for any advice. I’ve got a local farmer who has single phase to the farmhouse and 3 phase to the farm and dairy etc. The problem he’s got is when he turns the milking parlour on the house RCD trips. I am a bit stumped as to why and how to remedy. I was thinking when he switches the...
  19. S

    RCD Tripping out

    THIS IS FOR ELECTRICAL NEWS ONLY
  20. J

    Swapping out 3 way switch with dimmer, wiring mess found.

    Hey all. No stranger to electronics, I've been building simple circuits as a kid and these days I build computers. I have a kitchen fan with light fixture that the light is wired to 3 way switches on either side of the kitchen. I was going to replace one of the switches with a dimmer switch. I...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top