Search results | Page 2

Search results

You will need 50 posts under your account before joining in with this thread because you can't link out without 50 posts first.

  1. Flanders

    UK Wanting some quoting advice / am I about right/or too high-low

    agree with others that's a good price . I would also add on 5% for sundries . Covers the cost of screws, sleeving and that other wigit you forgot to allow for 😀
  2. Flanders

    No space in back box for dimmer modules

    Agree think the single box is also in a stud wall looking at the wood screw in the side fixing. A multi tool is your friend to deal within the noggin and then the box could be replaced with a deep dry lining box
  3. Flanders

    Avoiding EICR cowboys

    Yes its in gn3 that why I said in my post its guidance .
  4. Flanders

    Multiple lights and power socket not working but no blow fuses - any ideas?

    To check if the fuse is ok take it out of the switched spur and put in into a plug on an appliance you know works for example a table lamp. If the lamp works then the fuse is ok . If the lamp does not work then the fuse is blown which could of been course by a number of things . Either way...
  5. Flanders

    Plug/Fused Switch Outlet

    I saw it a lot in shop fitting all low bay lights on 13amp plug tops and everything else pluged into bus bar track above ceiling. What I dont like is 30 meters of flex going across a false ceiling with a 13 amp plug on the end to supply the intruder alarm system🤔
  6. Flanders

    Wiring supply in top of Isolators RCDS and mcbs

    I will speak to hager again and get a second opinion 😃
  7. Flanders

    Wiring supply in top of Isolators RCDS and mcbs

    When I spoke to hager tech about this they said that mcbs must be fitted the correct away round as I remember it ,it was to do with the direction the arc traveled in the event of a fault or overload
  8. Flanders

    Will this old switch have asbestos in it?

    It will probley have the asbestos flash pads in it think it will have 2 fuse holders
  9. Flanders

    Switchgear Brand Identification

    MEM and bill are the same. Schneider make square D kq and Merlin gerin. Although the same mcb Square d are plug on and Merlin are not. You used to be able to remove the plug on part of the square d mcb so you could fit it in a merlin board but they glue them in now . I think a lot of the no...
  10. Flanders

    Avoiding EICR cowboys

    The guidance is General Domestic is every 10 years or occupancy change . Domestic rented are every 5 years, that's where you maybe getting confused.
  11. Flanders

    Replacement DB to Submain RCD advice

    Ok so In this case I would not worry about selectivity. As you have a current EICR for the wylex DB and is not part of your alterations then I would just test up the wylex board. Compare zs at DB with EICR to confirm all final circuits from the wylex DB will disconnect under fault conditions...
  12. Flanders

    Replacement DB to Submain RCD advice

    I would say you are overthinking it. If your not altering any part of the office installation, then leave it alone ust test the circuits fed from your new DB. Does the office DB have a up to date EICR? Technically you should not use an mcb to feed a sub main as there will be no selectivity...
  13. Flanders

    C2 Vs C3 for no RCD on various circuits

    Because you are standing directly on the ground which is also possible wet. As you say less likely to get a larger shock standing on your wooden floor in your house. Also your more likely to cut through a cable with the hedge strimmer than a hairdryer 😀
  14. Flanders

    Switchgear Brand Identification

    nice work and as others have said some I have never heard of . Willrose electrical sell old mcb etc and have drop down lists of all the makes and models. This may help you create your list 👍 I notice Tenby is not on your list 😀
  15. Flanders

    Does SPD MCB size matter?

    The reg states it just something to be considered. So its up to you if you choose to follow it. I prefer to use separate rcbos, but if the spec requires a split load board thats what will be installed . Just to add regarding spds. Hagers connect straight to the main switch with no OCD in the...
  16. Flanders

    Does SPD MCB size matter?

    See Reg 531.3.2 unwanted tripping (ii) rcbos should be considered. Also see section 314
  17. Flanders

    Second Opinion on Modification to Existing Circuit

    The problem.. with sy cable is that its not recognised by bs7671 although there are tables on line with current carrying capacity detail. We only used it for long runs on 24 volt access control and BMS . But you see it all the time used on Air con systems. that not to say its correct and when...
  18. Flanders

    Why are there so many secrets during job planning

    You can get a good app for doing 2d / 3d drawing called floor plan creater. Only cost about £9 and is free to try out .then you have clear picture for where everything is going.
  19. Flanders

    Please tell me i'm not going mental and he's talking gibberish?

    I'm not sure if you can touch the top of the fuse carrier with the fuse remove, in those hager switched fuses, which in this case would be live. Where as the bottom of the fuse holded is not accessible. And that's why the live in should be in the bottom terminals
  20. Flanders

    UK Emergency lighting regs

    Agree the mains lights should stay on durring test mode except the combined ones of course. As suffolksparks says. The LED indicator will not be illuminated in test mode . And label the el fitting to avoid any confusion

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top