Search results | Page 2

Search results

  1. S

    Photocell Problem

    Get a new photocell. lol
  2. S

    Photocell Problem

    Either you have connected a permanent live to your outgoing switch live to light in your junction box or your photocell is broken. Best way to check is to go out remove your photocell if your light stays on the problem is with the wiring.
  3. S

    Lutron rania dimmer problem

    Thanks for all your help on this one guys sure i'll get to the bottom of it one way or another.
  4. S

    Lutron rania dimmer problem

    I've pulled a couple down and they were dimmable going to go back tomorrow and take everything down and check it, i've got a copy of installation guide and programming so i'll reset the switch and change it to ELV operation if necessary the kit might just be faulty.
  5. S

    Lutron rania dimmer problem

    Whats the difference between leading and trailing edge? I haven't actually installed any of the kit just been called in to sort it out along with other things someone else should have done right. Must sound like a right melon never touched the stuff and hopefully i never will again there's no...
  6. S

    Lutron rania dimmer problem

    There not GU10's there 12v Bi-pin 35w c/w transformers. I was wondering wether using a smaller lamp in the fitting may sort the problem down-rate them to 20w
  7. S

    Lutron rania dimmer problem

    only 450w this is probably a stupid question why does it need to be 700w
  8. S

    Lutron rania dimmer problem

    The installation has 11 x 35w lights which is 385w but lutron has suggested it's a problem with overcurrent, to be honest never touched the kit so don't know any of the problems with it. Read the installation guide and can't see any problem which what the previous electrician has done the switch...
  9. S

    Lutron rania dimmer problem

    I've been asked by a customer to look at a lutron rania dimmer. The problem is when switched on the lights flash light a strobe light all over the room. Spoke to lutron they believe that it overcurrent so I split the room lighting and still have same problem. Anyone come across this before...
  10. S

    Can anyone Recommend a software?

    Can't recommend any software but i'll send you a method statement and risk assessment on word which you can change and keep for each job.
  11. S

    Wago's , junction boxes and choc blocks whats best with downlighters

    I always use the ashley downlighter junction box with 1mm flex down to lights there a bit expensive but save time in the end and there's plenty of room for cables.
  12. S

    How do you protect your tools from been stolen?

    would it be illegal to charge a capacitor from car engine attached to the bare copper around your tools with no means of discharging, well unless some little thief discharged it to the ground. lol
  13. S

    How do you protect your tools from been stolen?

    My battery power tools are all hilti and i have a key fob to charge all the batteries. Doesn't stop them being stolen but i'll feel better knowing that they can't be used.
  14. S

    Double mcb for meter tails protection

    Cheers going swap a the main switch wylex tails isolator to a double pole mcb cheaper than a switch fuse. Cheers wirepuller
  15. S

    Double mcb for meter tails protection

    Im moving a consumer unit at customer request from garage into a cupboard understairs so customer doesn't have to leave house to get to unit. The tails would be 8m. I've considered using a type 'B' 80A DP MCB which will act as isolation and tails protection. Has anyone else used this method...
  16. S

    16mm T+E need for Dual earth?

    Hi Guys I've done a periodic on a small office today in the cellar there is a switch fuse with a 16mm T+E feeding a DB on 2nd floor with 2 ccts for offices with computers and a lighting circuit. The office ccts will have high earth leakage from computers 10+ on each circuit. The DB should...
  17. S

    Industrial or Commercial?

    Stroboscopic effect can occur in industry when flourestant fittings are installed on 1ph causing machinery to look as though it is stationery when it is not.
  18. S

    spare cores when using armoured help

    Spare cores in any electrical system should be earthed in case for any reason the become live under fault conditons
  19. S

    JIB graded me as labourer!

    Don't want to upset you guys but i haven't got NVQ3 or AM2 and got an approved grade with JIB this year. I've been in the trade 10 years and underwent training as an apprentice in the armed forces. As long as you provide detailed references showing your experience and your qualifications and a...
  20. S

    Industrial or Commercial?

    Install a 3ph DB in the workshop and run your lighting and sockets from that, leave enough extra ways for any extra equipment that may be required in future. Make sure you've correctly sized your cable for volt drop and loading alllowing extra capactiy as customer request. Don't forget about...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top