Hi, ive just received my copy of COP4th Edition.
It says that insualtion resistance test 500V dc might harm I.T. equipment and to use alternative method.
I am using Martindale EasyPat 2100 which cant do 250V dc. Can anyone recommend a portable test instrument for the alternative test methods...
can someone please explain insulation resistance testing to me i have read GN3 and brian scaddans book , i know it is to ensure conductor insullation has not deteriorated or damaged but i read posts on here about how you can use it to find borrowed neutrals and short circuits , and why does...
I have borrowed a multifunctional tester it's calibrated and works everything's good with it. I did a live to earth test and got a reading of .078 megaohms what does this translate too it is not my meter and I don't really do testing too much
I have a Metrel MI3000 MFT. It has given very low insulation resistance readings for a circuit I was testing earlier today (0.001MΩ) between live and earth(!) but the circuit has been working fine and not tripping the MCB (20A, no RCD as it is a pre-17th ed. CU) and I had tested it only a...
Hello Sparkies and Sparkettes.
Carrying out a IR tests I got a reading from the upstaris light (1.1 ohms) but could not get a reading of the downstairs lights, even though all bulbs were out and switches off. I could get no other reading from the other MCB's either e,g Ring, Shower, Cooker etc...
Hi
I am still training and have a question regarding Insulation resistance test.
My question is when doing the test between live and earth at the consumer unit, what happens to the circuit breakers? On or OFF?
Many thanks.
Hi guys,
Fairly recently qualified sparky here starting to do small solo jobs. I'm interested in views on insulation resistance testing on works to be signed off with a Minor Works Certificate. (Sorry this is a long post but I wanted to cover everything.)
One view on this is that you only test...
Evening all. Thought I would finally seek advice of those who know better! This is my first post so be gentle with me!
Just wired a new 3 bed house. All great until I test for ins. res. on final lighting circuit. Result came in at less than 1Mohm- [ L-E = 0.39, LN-E = same ] did all the usual...
insulation resistance test on a EICR/pir
have read in 'unite the union guide to inspect and test'
test carried out with L/N joined to Earth and no need to disconnect loads/vunerable devices
pic1 to test whole insulation, shows link between L/N (incoming) at main switch with supply isolated...
Hi guys,
I would just like to ask if any one could look at my test procedure off the top of my head and give any advice or pointers or whether its too long winded or short. got an exam in 2 weeks so trying to drill it in to this thick skull :)
Many thanks
Safe Isolation has been carried out...
Hi all, Tested a lighting circuit recently and got live to earth dead short and neutral to earth dead short on insulation resistance all loads were still connected there was a fluorescent fitting on the circuit and signs of green goo in switches and ceiling roses and the MCB was not tripping. Do...
Hello All,
I am to install some extra sockets for a customer on a relatively new build.
The insulation resistance test.
I tested at 250VDC between line conductors connected and earth and obtained a reading of 1.10 ohms (not megaohms)
Does this reading seem likely that a piece of equipment...
Hi all,
Just a quickie. I carried out an insulation resistance test on a lighting circuit which only has two rooms consisting of 4 lights.
Live to earth and neutral to earth was fine but when I tested live to neutral I got a short circuit.
All the bulbs were removed so just wondering if...
Hi All first post
I read that during the insulation resistance test of a 3 phase removal of the neutral incomer is necessary !
can some one please state the procedure for 3 phase IR tests
Thanks
Been to a Job this morning problems with RCD tripping, Global IR came back 0.016, Split circuits down and lighting tested (Including outside tested 0.018) however tested again 0.567 and then 1.03 each time the figure increases until it sits about 1.14. Testing done L&N - cpc and then N-Cpc...
When doing a CU change and lights have no cpc. Every room has class 2 dimmers and lights. ceilings are like 20 foot tall. How would you guys go about Insulation testing? L&n to cpc ain't an option and removing all lights and bypassing dimmers is consequently going to take some time... What would...
Hi i`m new poster, qualified electrician but not working as one just using it for my home.
I have installed an extractor fan with low voltage light in en-suite and now have to do a minor works tests.
I have done the resistance test an my readings are
l/n 0.8
l/e 1.7
n/e 1.3
earth fault loop...
Job is to extend a kitchen ring circuit, and have a question about Insulation Resistance values.
Tests on existing ring (2.5/1.5 t&e) carried out and results as follows -
Ring continuity (end to end)
R1-R1 = .38W
RN-RN = .42W
R2-R2 = .64W
Continuity W
R1-R2 = .34W
Insulation Resistance MW...
Hi
Was wondering if you could clear up a few things I on't quite understand, I've been told it is possible to do an insulation resistance test on a live DC cable (Solar pv) by testing to ground. Is this right, and what voltage rating should I set the megger to?
Also on a domestic solar pv...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.