Hey everyone
help needed please.
Moved into a new home, and have just had all the first fit installed for a new kitchen. During first fit, the electrician changed a socket on the kitchen ring and then moved onto another part. Within a few minutes the whole house tripped on the RCD. He retraced...
We have a lighting circuit on a dimmer and with 5A round pin sockets for standard lamps and table lamps (ie: no ceiling roses)
After about 7 years of reliable use it started to take our trip out (and the dimmer!) Mostly intermittent but almost instantaneous now.
Fault-finding showed that if...
Hi guys,
I plan on installing a ring floodlight onto the brick centered above my garage door. I have some pictured attached I marked in red where I plan to run cables. My brother has done some electrical work but is not licensed electrician. Based on my research and his knowledge it seems right...
Hi guys
Got a little dilemma. Customer has 3 up and down wall lights in back garden, one either side of the extension and one centre. All three switch on from wall light inside the house.
They've asked if I could swap the centre light with a ring floodlight camera. Upon checking...
Hi,
I've recently had a storage heater installed. This was installed in a location that didn't have an off-peak supply.
After some investigation, the electrician moved some wires in the fuse box, to make one of the plugs an off-peak supply. However, this has now impacted: 1 x towel heater in...
Hi,
I've just been testing a ring final before installing an outdoor socket and I got an R1 and rn of 0.6, but instead of 1.01 for R2 I got a range of readings from 0.1 to 0.51 and it wouldn't settle down, so I couldn't continue the tests.
I know parallel paths could cause a low reading, but...
I have had a new boiler fitted yesterday but the supply to the boiler has moved. The boiler is currently on a normal 3 pin plug plugged into a socket. What I want to do is have it wired into a fused spur. But in the future I want to run armoured cable to my shed off another fused spur on the...
i walked a model home yesterday and it had been fitted with can lights that had a typical downlight, but the standard downlight trim would also emit a soft glow around the edge as an option as well. Basically the light switch toggled between those options: Downlight on, dim edge glowing only...
Hi there all,
I have a property and I have noticed the following wiring (please see below) in one of the rooms in the house.
It looks like the ring circuit has been extended.
A single 2.5mm Twin + Earth cable (in red) is providing power from the consumer unit which feeds a chain of electrical...
Hi everyone
my questions is regarding a ring circuit wired in 2.5mm standard twin n earth with 32A MCB however my question is hypothetical if there are 2 laundry and 2 lets say tumblers so load is not suitable for the circuit and you want to upgrade but there is no space in consumer unit to...
Hi
I’m after some advice please. I’m on a job where there’s a junction box with ring main wired in singles through 50x50 galv trunking. I need to break into this ring for my additional sockets but need to identify which of the cables are incoming and outgoing ones!? I can’t follow cable in...
Hi all,
Hoping you can help.
My house has a ring in the kitchen that is no longer wired direct to the consumer unit as it had a fault and kept blowing. It was believed that it might be an 'open ring' and a socket had been removed from the ring at some time in the past. (I think that was what...
Hi,
Newbie here and DIY homeowner looking for advice. I found a spur in our house with 5 double sockets on. Ideally I would like to keep the sockets, so am thinking about incorporating it into the ring by bringing the cable back from the end of the spur in to the next socket on the ring.
It...
Hey guys,
I recently bought and installed a Ring Doorbell Wired. I followed the instructions and installed it into my existing doorbell wiring.
Just a few days later I realized that it was “Offline”. There haven’t been any power outages, the wifi and pw are unchanged.
So I ran through the...
Hi - my 1 year old table top freezer causes audible clicks on my (good quality) audio equipment every 15-30 minutes as it turns on/off. What is particularly surprising to me is that the clicks only happen when the freezer and audio are on the same mains ring. I have monitored the output of the...
Here's one I wasn't expecting on an EICR. Recently rewired and renovated 2-bed property (2015ish). Having an EICR as a new tenant to move in soon. No reported problems.
I expected to be in and out in about 3-4 hours to be honest, and as expected I found nothing wrong until I began my ring final...
Okay, so, I’m currently working towards becoming an electrician and was after some guidance for a job that I’m working on.
The property (a small flat) has a few circuits on RCBOs.
1 Ring (kitchen)
1 Radial Sockets
1 Internal Lighting
1 External Lighting
The owner occupier is replacing their...
Hi everyone, so ive got a new oven to install this one is rated at 16 amps, old one was 13 amps on a plug and socket to ring main. My question is can i install a 32amp double pole switch on the ring main then feed 4mm flex to the oven? Is there anything in the regs that prevents this? Thanks for...
Hello
Need guidance powering / charging a RING Pro video doorbell. Have an old home intercom system M&S MC602 (its powered by TE-5B transformer120v input).
I have the exact setup as this thread.
https://www.doityourself.com/forum/h...om-system.html
My apologies in advance I'm very green when...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc